Range Rover Classic Parts

Piston Ring Set for the 300TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. Fo...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Oil Cooler Hose forms part of the engine oil cooling circuit on the 200TDi. It runs between the oil cooler and the oil pump/filter housing, carryi...

Timing Belt Tensioner for the 200TDi 2.5L turbo diesel engine, part of the camshaft timing belt drive. The tensioner maintains correct tension on ...

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Banjo bolt

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Head Gasket Set - V8

Ignition Module & Link Lead - a kit for the 3.5L Rover V8 petrol engine ignition system, comprising the electronic ignition module (amplifier) ...

Double Cardan Joint Kit for the Discovery 2 front propshaft. The Discovery 2 front propshaft uses a double cardan joint assembly incorporating thr...

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Heavy Duty spring Range Rover rear +0mm

Crankcase Breather Hose forms part of the closed crankcase ventilation circuit, connecting the rocker cover breather outlet to the intake manifold ...

Steering knuckle fulcrum bracket assembly used within the front axle swivel and steering knuckle pivot arrangement. The bracket forms the lower p...

The cable forms the mechanical link between the handbrake operating lever and the handbrake mechanism within the handbrake assembly, transmitting l...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

A-Frame Ball Joint Bracket forms the pivot connection at the apex of the rear axle A-frame linkage. It mounts to the rear axle housing and locates ...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Coolant Expansion Tank with a clear (translucent) body, part of the engine cooling system. The tank serves as the system's pressurised reservoir a...

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Steering Column Lock - the steering column lock and ignition switch assembly. Mounted on the steering column, it mechanically locks the column whe...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Radiator Hose - Bottom - V8 Petrol

Bottle sensor

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Exhaust Bracket supports and locates a section of the exhaust system against the underbody. It carries the weight of the exhaust at its mounting p...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 5th gear selector bias. It works within the gear lever remote housing...

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Pedal Box Pivot Bolt for the pedal box assembly, forming the pivot axis on which the brake or clutch pedal swings within its mounting bracket. The...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Power Steering Hose - the high-pressure feed line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pu...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...