Range Rover Classic Parts

Conrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Receiver Dryer for the air conditioning system, compatible with R134a refrigerant. Installed on the high-pressure side of the A/C circuit, between...

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

special bolt for rocker shaft 200 TDI three per engine. sold EACH! - 90/110/130 - Discovery - Range Rover Classic

Shaft coupling

Outer Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Front Coil Spring, part of the front coil-sprung suspension. The spring fits between the chassis spring seat and the front axle, supporting vehicl...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Heater Bypass Coolant Valve for V8 petrol applications. This vacuum-operated valve is installed in the HVAC coolant circuit and controls the flow ...

Thermostat Housing for the 2.5L 300TDi 4-cylinder turbo diesel engine. This housing secures the engine thermostat within the cooling circuit and f...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Joint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...

Gear Lever Bias Plate for the manual gearbox gear change mechanism. It sits in the gear lever remote housing and works with the bias spring to load...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Switch window lift

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Drain Plug - Coolant - Cylinder Block is the threaded plug that seals the coolant drain port in the cylinder block, providing a controlled drain po...

Trunnion

Front Coil Spring - front suspension coil spring, seated between the axle spring pad and the chassis spring turret to support the vehicle and contr...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Cable Tie, Panel Fixing: grey cable tie strap with a panel fixing, 4.6 x 165 mm.

Pulley

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Fuse - 10A for Land Rover electrical systems. This 10A fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...