Range Rover Classic Parts

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This is the pl...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Thermostat Housing Gasket for the engine cooling system. This top gasket seals the joint between the thermostat housing and the engine, preventing...

Steering drop arm lever for left-hand drive steering box applications. This component connects the steering box output shaft to the steering linka...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Radius Arm Bump Stop - Rear for the rear suspension radius arm assembly. This bump stop limits upward suspension travel at the rear axle, providin...

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Headlamp for the front lighting system: a 7-inch round unit with a flat glass lens. The lamp takes a replaceable H4 halogen bulb, giving combined ...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Hex Nut - 5/16" UNF is a plain hexagonal nut with a 5/16 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis...

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Joint washer (non-ABS)

Front Hub Nut for the front hub and driveshaft assembly, retaining the wheel hub and bearing assembly on the stub axle. This large-diameter locknu...

Accelerator Pedal Pad - a moulded rubber pad fitted over the accelerator pedal arm, providing a textured grip surface for the driver's foot and pro...

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...

Spring Retainer Ring for the front coil spring on the suspension. The ring secures the coil spring to its seat, holding the spring captive so that...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Tap screw

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Front cover oil seal

Fulcrum Bracket and Ball Joint Assembly for the rear A-frame (top link). The bracket forms the apex of the A-frame and bolts to the rear axle; the ...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Exhaust Gasket - V8 for the exhaust downpipe assembly on V8 petrol engines. This gasket seals the flange joint at the exhaust downpipe, maintainin...

Exhaust Gasket for the front exhaust section on 2.5L TDi and V8 petrol engines. On 2.5L 200 TDi and 300 TDi 4-Cylinder engines this gasket seals t...

Shock absorber bush (eye), anti roll bar bush

Steering Damper Stabiliser - a hydraulic damper fitted within the steering linkage assembly to control the oscillation and vibration transmitted th...

Circlip for the drive shaft and hub assembly on Land Rover permanent four-wheel drive axles. This circlip locates in a machined groove on the driv...

Side Repeater Lamp - Front is part of the exterior lighting system, mounting in the front wing to give a side-on indication of the direction indica...

Windscreen Washer Pump, 12V electric, for the windscreen washer system. The pump draws screen-wash fluid from the washer reservoir and delivers it ...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

This taper roller bearing is designed for installation in the lower swivel pin housing, providing controlled rotational support and load distributi...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...