Range Rover Classic Parts

O-Ring for the LT77 five-speed manual gearbox. It seals the mainshaft and extension case joint against transmission oil loss.

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Intercooler Hose the upper charge-air hose in the intercooler circuit of the 200TDi diesel engine. It carries cooled, pressurised charge air from ...

Propshaft Nut - Rear - nut retaining the rear propshaft flange at the rear differential pinion. The nut clamps the propshaft coupling flange again...

Rock guards, rock sliders (pair) galvanised. Fits Discovery 1 and Range Rover Classic (except LSE)

Castor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...

Relief Valve Spring is the coil spring that controls the opening pressure of the oil pressure relief valve in the 300Tdi engine lubrication system....

Sending is only possible by pallet. Too fragile for normal parcel delivery.

EGR Pipe Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine. This rubber hose forms part of the exhaust gas recirculation (EGR) circuit, conn...

Swivel Pin Thrust Washer - Upper is the shim washer that sits above the upper swivel pin bearing in the front axle swivel housing assembly. It set...

Differential Fixing Bolt used on the front and rear axle differential assemblies. It is one of the bolts securing the differential assembly, clamp...

Rear Wheel Arch Front Extension - RH is the front section of the right-hand rear wheel arch extension for 2-door bodyshells. It forms the leading ...

Outer Sill - external sill panel for the right-hand side of the two-door body. The outer sill is the visible rocker panel spanning the lower body b...

Trailer Plug - a 7-pin towing electrics connector. Wired into the towing vehicle's harness, it mates with the trailer or caravan socket to feed th...

Copper Sealing Washer - a crush washer used to seal banjo and union connections throughout the diesel fuel system, at fuel pipes, filters and sedim...

Mudflap Bracket - Front - LH secures the front mudflap to the body on the left-hand side of the vehicle. Part of the front mudflap assembly, the b...

Mudflap Bracket for the front, right-hand side. This bracket secures the front mudflap to the body, holding it at the correct position behind the ...

Synchromesh Ring for the five-speed manual gearbox mainshaft. The synchro (baulk) ring matches the speed of the gear to the synchro hub before eng...

Shock Absorber A hydraulic telescopic shock absorber (damper) for the front suspension. It damps spring oscillation to control body movement and m...

Vacuum Pump Rotor Blade for the engine-driven brake servo vacuum pump. The blade runs within the rotor of the vacuum pump, generating the vacuum t...

set screw M6 x 25mm 8.8 various applications

Transfer Box Differential Lock Clevis in the centre differential lock linkage. Connects the diff-lock actuating linkage that engages and releases ...

Thrust Washer - intermediate shaft thrust washer for the LT95 four-speed gearbox. It controls the end-float of the intermediate (lay) shaft, takin...

Rear Wheel Arch Extension - Front Section, Left-Hand for the two-door body, an exterior body trim panel. This extension fits to the forward part o...

Joint Washer for the manual gearbox top cover. This gasket seals the joint between the top selector cover and the gearbox case, retaining the gearb...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Detent Spring for the LT230 transfer box. It loads the detent that holds the high and low range and differential lock selectors in position, preven...

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

Bush for the axle and suspension assembly. This bush fits within a suspension or axle mounting point to absorb vibration and provide compliant art...

lead link pump washer 90/110 used to fit newer style washer pumps to earlier vehicles

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Radiator Frame – Top, the upper section of the radiator mounting frame. The top frame retains and locates the upper edge of the radiator within th...

Universal Joint, heavy-duty, for wide-angle propshafts. The wide-angle geometry allows the joint to operate at the increased angles produced by li...

Swivel Pin Bearing is the upper needle-roller thrust bearing in the front axle swivel housing assembly. It mounts on the upper swivel pin and carr...

Distributor Base Plate - the base plate assembly inside the V8 distributor, carrying the magnetic pick-up for the electronic ignition. The pick-up ...

Thrust Washer - mainshaft thrust washer for the R380 five-speed manual gearbox. Located at the mainshaft 5th/reverse gears, it controls end-float ...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Coil Spring Conversion Kit that replaces the Electronic Air Suspension (EAS) with conventional coil springs, eliminating the recurring faults and m...

Baulk Ring - synchroniser baulk ring for the R380 five-speed manual gearbox. Serves the mainshaft 3rd/4th and 5th/reverse synchroniser hubs, match...

Screw used as a body and underbody fixing across several assemblies, including the tailboard striker, the folding side-door step assembly, and the ...

Polyurethane Suspension Bush Set in the black compound, for the front and rear coil-sprung suspension. This is a full-vehicle set that replaces the...

Steering Shaft - the intermediate shaft in the steering column assembly. It links the steering column to the steering box input, transmitting rotat...

Footwell Repair Panel - Right-Hand is a weld-in body repair section for the front footwell of the floor assembly. It replaces the original offside...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

M5 blind rivet nut (nutsert) - a threaded insert for sheet-metal and box-section fixings. The nutsert is placed in a single drilled hole and set w...

Ignition Lead - King The king lead in the high-tension ignition circuit. It carries the high-tension output from the ignition coil tower to the ce...

Carburettor Needle is the tapered metering needle that sets the fuel mixture in the carburettor. The needle moves within the jet to control fuel d...

Nut A 4BA hex nut used as a threaded fastener. Applied on the door lock linkage and rear bumper mountings.