Range Rover Classic Parts

Oil Drain Pipe Gasket for the turbocharger oil return line on the 300TDi 2.5L turbo diesel engine. It seals the flanged joint where the external o...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Bolt Threaded fastener used within the exhaust system assembly.

Relay

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Crown Wheel Bolt secures the crown wheel (ring gear) to the differential carrier within the axle differential. Threaded 3/8 UNF and 1.1/8 inch lon...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Transfer Box Output Shaft Mud Shield fitted at the output shaft oil seal of the LT230 transfer box. The shield sits over the output shaft ahead of...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

O-Ring for the fluid suction pipe of the ZF four-speed automatic transmission. Seals the joint at the suction (pick-up) pipe that draws automatic ...

Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

Fuel Temperature Sensor for the EFI V8 petrol engine, part of the electronic fuel injection management system. The sensor measures the temperature...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Shaft coupling

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Cable Tie, Panel Fixing: grey cable tie strap with a panel fixing, 4.6 x 165 mm.

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Fuse - 10A for Land Rover electrical systems. This 10A fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Oil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...

Mudshield

Yoke Transmission

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Clevis pin

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Throttle Potentiometer Gasket seals the throttle position sensor (throttle potentiometer) to the throttle body on the V8 EFI system. It forms the ...

Plenum Chamber Gasket for the V8 EFI petrol engine, part of the air intake and induction assembly. The gasket seals the joint at the plenum chambe...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...