Range Rover Classic Parts

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Pedal Box Pivot Bolt for the pedal box assembly, forming the pivot axis on which the brake or clutch pedal swings within its mounting bracket. The...

Pull Ring for the rear seat lock release. It operates the split rear seat lock mechanism, releasing the seat squab so the backrest can be folded d...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Propshaft Spacer Kit (25mm) - a driveline spacer fitted between the propshaft flange and the transfer box or differential flange to restore the pro...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Bolt and Washer - an M8 x 25 mm hexagonal-head bolt supplied with a washer. A general-purpose threaded fastener used at various fixing points on t...

Locknut is a self-locking M10 nut used as a general threaded fastener across the vehicle. Its locking feature resists loosening under vibration, m...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Exhaust Flange forms a bolted joint in the exhaust system of the early 3.5L V8 petrol engine with single downpipes. It provides the sealing face w...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Rear Exhaust Assembly - the rear section of the exhaust system, carrying the exhaust gases from the mid-section back to the tailpipe. Supplied as ...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Fuel Hose for the 3.5L V8 twin-carburettor engine, part of the carburettor fuel supply plumbing. It connects the fixed points in the fuel feed lin...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Changeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Bolt - 5/16" UNF x 3-3/4" A 5/16" UNF setbolt, 3-3/4" long, catalogued for use across several applications. Its uses include securing the timing/f...

Front Door Hinge Set Screw secures the front door hinge to the body pillar and door within the door mounting hardware. It clamps the hinge leaf in...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Modular Steel Wheel - Black - 7J x 16 A modular steel road wheel finished in black, sized 7J x 16 with an ET08 offset. The steel construction suit...

Cylinder Head Bolt for the 200TDi 2.5-litre direct-injection turbo diesel engine. It secures the cylinder head to the engine block, clamping the he...

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Dislocation Cone - Rear Coil Spring for the rear coil spring seat assembly. When long-travel shock absorbers or lowered top-mount shock relocators...

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Split Pin - Rear Upper Shock Absorber Mount for the Range Rover Classic rear suspension assembly. This split pin secures the retaining bolt or piv...

Tailgate Seal for the rear end structure. This seal fits around the tailgate aperture, sealing the joint between the tailgate and the rear body to...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Transmission Brake Drum for the transmission (hand) brake. Mounts to the transfer box rear output flange and houses the transmission brake shoes, ...

Alternator is the charging-system generator that supplies current to the battery and vehicle electrical system. Driven from the crankshaft by the ...

Return to Centre Steering Damper for installation within the steering linkage assembly. This unit mounts between the axle steering arms and the st...

Rear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Bracket

Rocker Cover Gasket Set for the 2.5L VM turbo diesel engine, sealing the rocker cover to the cylinder head. The gasket seats between the rocker co...

Bolt is a general-purpose imperial-thread fixing with a 5/16-inch UNC (Unified Coarse) thread and a 7/8-inch length. Used as a common fastener acr...

Window Motor for the right-hand front door, part of the electric window regulator assembly. It drives the regulator mechanism to raise and lower th...

Window regulator front RH

Hub Oil Seal for the front axle, sealing the front hub and drive shaft assembly to retain hub lubricant and exclude water, dirt and grit from the w...

Carburettor Gasket Kit for the Zenith/Stromberg 175CD carburettor fitted to the 3.5L V8 petrol engine. The kit supplies the renewable gaskets and ...

Indicator Lamp - Front - LH The left-hand front direction indicator (flasher) lamp, part of the front exterior lighting assembly. Mounted at the f...

Side Repeater Lamp is the front side turn-signal repeater within the exterior lighting and direction indicator system. Mounted on the front wing, ...