Range Rover Classic Parts

Synchromesh Ring for the five-speed manual gearbox mainshaft. The synchro (baulk) ring matches the speed of the gear to the synchro hub before eng...

Shock Absorber A hydraulic telescopic shock absorber (damper) for the front suspension. It damps spring oscillation to control body movement and m...

Rear Coil Spring for the rear suspension, raising ride height by approximately 40mm over standard. Wound from 18mm wire with a free height of 445m...

Vacuum Pump Rotor Blade for the engine-driven brake servo vacuum pump. The blade runs within the rotor of the vacuum pump, generating the vacuum t...

set screw M6 x 25mm 8.8 various applications

Rear Lamp Lens for the left-hand side, forming the outer cover of the rear lamp assembly. The lens fits over the lamp body to seal and protect the ...

R380 five-speed manual gearbox, suffix 55A-J, supplied reconditioned. The R380 is the manual transmission that sits between the engine and the tran...

Screw, M6 x 45, used as a threaded fastener at several points in the drivetrain and pedal assemblies. It secures the lower bellhousing cover to th...

Weld-On Beadlock Ring Kit - a set of four steel beadlock rings for converting 16in steel wheels to a mechanically clamped tyre bead. The inner rin...

Front Pipe with Catalytic Converter forms the leading section of the exhaust system on the V8 petrol engine equipped with catalyst, mounting betwee...

Transfer Box Differential Lock Clevis in the centre differential lock linkage. Connects the diff-lock actuating linkage that engages and releases ...

Dowel, used with 3-bolt flange. (For Hardy coupling)

Thrust Washer - intermediate shaft thrust washer for the LT95 four-speed gearbox. It controls the end-float of the intermediate (lay) shaft, takin...

Wheel Chock for securing a stationary vehicle. Placed against a tyre, the wedge-shaped chock prevents the vehicle from rolling when parked on an i...

Input Shaft is the primary (input) shaft of the manual gearbox, carrying drive from the clutch into the gear train. It takes the clutch output on ...

Anti-Roll Bar Bush locates the anti-roll bar at its mounting to the chassis, holding the bar in position while allowing it to rotate as the suspens...

Exhaust Valve for the cylinder head valvetrain of the 200TDi and 300TDi 2.5L turbo diesel engines. It seats in the cylinder head exhaust port and ...

Layshaft Bearing for the front of the LT77 five-speed manual gearbox layshaft. The bearing supports the forward end of the layshaft (countershaft)...

Rear Wheel Arch Extension - Front Section, Left-Hand for the two-door body, an exterior body trim panel. This extension fits to the forward part o...

Joint Washer for the manual gearbox top cover. This gasket seals the joint between the top selector cover and the gearbox case, retaining the gearb...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Polyurethane Suspension Bush Kit - Classic Red grade. This kit replaces the original rubber suspension bushes with polyurethane items in the Polyb...

Detent Spring for the LT230 transfer box. It loads the detent that holds the high and low range and differential lock selectors in position, preven...

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

Bush for the axle and suspension assembly. This bush fits within a suspension or axle mounting point to absorb vibration and provide compliant art...

lead link pump washer 90/110 used to fit newer style washer pumps to earlier vehicles

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Cold Air Intake Filter replaces the complete air filter box in the induction system with an exposed reusable filter, drawing cooler air to the engi...

Radiator Frame – Top, the upper section of the radiator mounting frame. The top frame retains and locates the upper edge of the radiator within th...

Universal Joint, heavy-duty, for wide-angle propshafts. The wide-angle geometry allows the joint to operate at the increased angles produced by li...

Thrust Washer is a 1.05mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Rear Inner Wing - right-hand side, two-door bodyshell. Weld-in structural repair panel. The inner wing forms the inboard wall of the rear wheel ar...

Shock Absorber - front gas-charged suspension damper. Mounted between the front axle and the chassis, it damps spring oscillation to control body ...

Mudguard - Power Take Off for the centre power take-off (PTO) housing. Mounted to shield the centre PTO unit from mud, water and road debris. Prot...

Fuel Pipe Olive is a compression ferrule used to seal a rigid fuel pipe union. The olive is compressed onto the pipe by the union nut to form a le...

Motor assembly front & rear door window regulator LH

Selector Cover Gasket - LT95

Drain Plug - a threaded plug that seals a drain point and is removed to drain fluid during service. It is used in several locations depending on ap...

Oil Pump Gasket for the LT95 four-speed gearbox. It seals the oil pump to the gearbox casing on the LT95 transmission, used behind the Rover V8 an...

Swivel Pin Bearing is the upper needle-roller thrust bearing in the front axle swivel housing assembly. It mounts on the upper swivel pin and carr...

Piston Ring (+.020" Oversize) for the 2.5L 200 TDi four-cylinder turbo diesel engine, forming part of the piston, connecting rod and bearing assemb...

Distributor Base Plate - the base plate assembly inside the V8 distributor, carrying the magnetic pick-up for the electronic ignition. The pick-up ...

Thrust Washer - mainshaft thrust washer for the R380 five-speed manual gearbox. Located at the mainshaft 5th/reverse gears, it controls end-float ...

Locking Nut, a self-locking fixing used across body trim, door casings and bumper fixings. The locking feature resists loosening under vibration.

Rear Inner Wing - left-hand side, two-door bodyshell. Weld-in structural repair panel. The inner wing forms the inboard wall of the rear wheel arc...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Coil Spring Conversion Kit that replaces the Electronic Air Suspension (EAS) with conventional coil springs, eliminating the recurring faults and m...

Differential Bearing Shim - 0.063in