Range Rover Classic Parts

Brake Disc, front, vented. Part of the front braking system. The disc mounts to the front wheel hub and rotates with the wheel; the brake caliper ...

Voor LT77 versnellingsbak

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Oil Cooler Pipe - the pipe carrying engine oil from the engine to the oil cooler within the lubrication cooling circuit of the 2.5L 4-cylinder TDi ...

Oil Cooler Pipe - the pipe carrying engine oil between the oil cooler and the engine within the lubrication cooling circuit of the 2.5L 4-cylinder ...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Drive Belt is the auxiliary drive belt for the 3.5L V8 petrol engine. Running from the crankshaft pulley, it drives the alternator and, where fitt...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Cylinder Block Drain Tap threads into the coolant jacket of the cylinder block, providing a controlled drain point for the engine cooling system. ...

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Bypass Hose for the engine cooling system of the 200 TDi diesel engine, connecting into the coolant pump. It carries coolant on the bypass route t...

Coolant Expansion Tank Cap - pressure cap for the cooling system expansion tank, rated at 15 psi. The cap seals the expansion tank and regulates s...

O-Ring for the engine cooling system thermostat housing. This sealing ring fits the drain or filler plug on the thermostat housing, providing a le...

Hose assy reservoir to pump Defender TD5

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Drag Link Ball Joint Kit for the steering box drop arm on power-assisted steering boxes. The ball joint forms the articulating connection between ...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Headlamp washer jet RRC Discovery 1

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Hex Nut with a 7/8" UNF (Unified National Fine) thread, used on the power steering box assembly. This large six-sided fastener threads onto a matc...

Spring Retainer - rear inner-top retainer in the coil spring and shock absorber mounting. It locates and holds the top of the rear coil spring at ...

7" round LED headlamp 12/24V chrome 78W LHD (pair)

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Front driveline propellor shaft connecting the transfer box output to the front axle differential within the drive mechanism. (60cm in 65cm) Trans...

Clutch Release Bearing Staple is the spring retention clip that secures the clutch release bearing onto the release fork. It holds the bearing in p...

Speedometer Drive Gear for the LT230 transfer box, located on the rear output and driving the speedometer take-off. This is the 20-tooth gear, ide...

Thermostat 74C

Automatic Drive Belt Tensioner for the front-end accessory drive system, maintaining correct tension across the auxiliary belt that drives the alte...

Spark Plug Ignition component for the Rover V8 petrol engine. Threaded into the cylinder head, it carries the high-voltage current from the igniti...

Coolant Bypass Hose for the engine cooling system of the 200 TDi diesel engine. It carries coolant along the bypass path so that flow continues to...

EGR Blanking Kit replaces the exhaust gas recirculation (EGR) valve on the 300 Tdi engine, sealing the EGR port on the intake manifold so exhaust g...

Facia Louvre Vent Housing for air-conditioned models, mounted in the facia as part of the cabin air distribution system. It carries the directiona...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Panhard Rod Bushes are the mounting bushes at the ends of the front panhard rod in the coil-sprung front suspension. The panhard rod locates the fr...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Locking plate

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...