Range Rover Classic Parts

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Thermostat Housing Gasket for the engine cooling system. This top gasket seals the joint between the thermostat housing and the engine, preventing...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Headlamp for the front lighting system: a 7-inch round unit with a flat glass lens. The lamp takes a replaceable H4 halogen bulb, giving combined ...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Hex Nut - 5/16" UNF is a plain hexagonal nut with a 5/16 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis...

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Front Hub Nut for the front hub and driveshaft assembly, retaining the wheel hub and bearing assembly on the stub axle. This large-diameter locknu...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Front cover oil seal

Tap screw

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Shock absorber bush (eye), anti roll bar bush

Steering Damper Stabiliser - a hydraulic damper fitted within the steering linkage assembly to control the oscillation and vibration transmitted th...

Side Repeater Lamp - Front is part of the exterior lighting system, mounting in the front wing to give a side-on indication of the direction indica...

Windscreen Washer Pump, 12V electric, for the windscreen washer system. The pump draws screen-wash fluid from the washer reservoir and delivers it ...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Grommet

Water Pump Inlet Gasket - seals the water pump inlet housing against the engine front cover within the coolant circuit. It forms the joint between...

Timing Chain for the Rover V8 petrol engine, part of the camshaft drive assembly located in the front timing cover. This single-row roller chain t...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

Enhance the ignition performance of your Land Rover Defender, Discovery 1, and Range Rover Classic (3.5 V8 carb & EFI models) with this high-qu...