Range Rover Classic Parts

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M6 thread with a 1...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Bolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap). A miniature bayonet bulb used in number plate, side, interior and rear lamp positions.

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Setscrew is a fully threaded hex-head fastener used as a general-purpose fixing across engine and cooling assemblies. Threaded 5/16" UNC with a 5/...

Clutch Master Cylinder Overhaul Kit

Oil Temperature Sender for the engine oil temperature gauge circuit. The sender threads into the oil gallery and carries a temperature-sensitive re...

Split Pin - a cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the shank or the nu...

Reverse lamp switch LT85 V8

Exhaust Flange forms a bolted joint in the exhaust system of the early 3.5L V8 petrol engine with single downpipes. It provides the sealing face w...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Bolt - 5/16" UNF x 3-3/4" A 5/16" UNF setbolt, 3-3/4" long, catalogued for use across several applications. Its uses include securing the timing/f...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Bolt is a general-purpose imperial-thread fixing with a 5/16-inch UNC (Unified Coarse) thread and a 7/8-inch length. Used as a common fastener acr...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Transfer Case Bottom Cover Gasket for the LT95 combined gearbox and transfer case. It seals the joint between the bottom cover and the transfer ca...

O-Ring - LT95 Gearbox seals the transfer shaft on the LT95 4-speed gearbox, which carries an integral transfer case, preventing oil leakage at the ...

Plain Washer M8

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Pas op alle  V8 benzine motoren met Stromberg carburateurs

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...