for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
High Pressure Fuel Pump Tappet drives the engine-mounted high-pressure fuel pump from the camshaft. The tappet acts as the cam follower, riding on...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsDiesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...
View full detailsTyre Pressure Monitoring Sensor (TPMS), a 433 MHz wheel-mounted unit that fits to the valve inside each road wheel. It measures tyre pressure and t...
View full detailsIgnition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...
View full detailsIgnition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...
View full detailsExhaust Camshaft for the 2.0L 16V turbocharged petrol engine (Si4 GTDi). Located in the cylinder head as part of the valve train, the camshaft's lo...
View full detailsImmobiliser Transceiver for the vehicle anti-theft (immobiliser) system. This is the transceiver aerial that reads the transponder in the key at t...
View full detailsAxle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...
View full detailsAxle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...
View full detailsBrake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...
View full detailsBrake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...
View full detailsBattery Management System sensor for the negative battery terminal, forming part of the vehicle's battery monitoring and charge-control circuit. I...
View full detailsRetaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...
View full detailsClip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.
Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...
View full detailsCylinder Head Gasket sealing the cylinder head to the engine block. Fitted to the 2.0L four-cylinder AJ200 (Ingenium) petrol engine, including PHE...
View full detailsParking Sensor for the park distance control (PDC) system, used in both front and rear bumper positions. The sensor mounts into its aperture in th...
View full detailsExterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...
View full detailsParking Sensor is a Park Distance Control (PDC) ultrasonic sensor mounted in the bumper, part of the parking aid system. It emits and receives ult...
View full detailsKeyless Entry and Start Aerial is the receiver antenna for the passive keyless entry and push-button start system, part of the vehicle's anti-theft...
View full detailsRemote Control Receiver is part of the vehicle anti-theft alarm system, operating on the 433MHz radio frequency band. It receives the coded radio ...
View full detailsBrake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...
View full detailsOil Level Sensor for the 2.0L 16V TiVCT turbocharged petrol engine, fitted to the oil pan (sump). The sensor measures engine oil level and reports...
View full detailsBrake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...
View full detailsLED Mirror Indicator Kit - a pair of direction indicator modules that replace the original repeater units in the door mirror housings. The modules...
View full detailsFuel Pressure Sensor for the high-pressure fuel injection circuit on petrol engines. It measures fuel rail pressure and temperature and reports to ...
View full detailsPrimary Timing Chain Tensioner from the timing drive assembly at the front of the 2.0L four-cylinder AJ200 / AJ20P4 engine. The tensioner bears ag...
View full detailsTiming Chain - Secondary, Upper is part of the camshaft drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4), including plug-in ...
View full detailsLamp - Side Flasher
Thermostat and Housing assembly for the 2.0L 16V TIVCT turbocharged petrol (GTDi) engine. The thermostat regulates coolant flow to bring the engine...
View full detailsEngine Knock Sensor for the 2.0L 16-valve turbocharged petrol engine, mounted on the cylinder block as part of the engine management system. The s...
View full detailsD3S xenon headlamp bulb, supplied with its igniter, for headlamp units originally built as bi-xenon or adaptive xenon assemblies. D3S is a mercury...
View full detailsFuel Filter for petrol applications, mounted in the rear fuel line assembly alongside the carbon canister and evaporative leak-detection components...
View full detailsWater Pump circulates coolant through the engine cooling system. Driven from the engine, it pumps coolant through the block, cylinder head and rad...
View full detailsFuel Pressure and Temperature Sensor for petrol fuel-injection systems. The combined sensor measures fuel rail pressure and fuel temperature and r...
View full detailsBumper Retainer Nut - a push-in retaining nut used in the front bumper, radiator grille and rear bumper assemblies. The retainer clips into a pres...
View full detailsBolt for the exhaust system front section. This fastener secures the flanged joint between the exhaust manifold and the front pipe section, holdin...
View full detailsTurbocharger Oil Feed Pipe for the turbocharger lubrication circuit. Carries pressurised engine oil from the oil supply to the turbocharger bearin...
View full detailsWater Pump circulates coolant through the engine cooling system. Driven from the engine, it pumps coolant through the block, cylinder head and rad...
View full detailsOil Separator is the crankcase ventilation (PCV) oil separator for the 2.0L 16V turbocharged petrol engine. It sits in the crankcase breather circ...
View full detailsHex Head Bolt - threaded fastener used at the engine mountings and at the front suspension strut mounting. Driven with a standard spanner or socke...
View full detailsTurbocharger Oil Feed Pipe for the turbocharger lubrication circuit. Carries pressurised engine oil from the oil supply to the turbocharger bearin...
View full detailsThermostat Housing for the 2.0L Ingenium petrol engine (AJ200P, including PHEV applications). The housing holds the coolant thermostat and forms p...
View full detailsIgnition Coil for the engine ignition system. It steps up battery voltage to the high voltage needed to fire the spark plug and is mounted directly...
View full detailsVVT Solenoid is the exhaust-camshaft variable valve timing control solenoid for the 2.0L 16V turbocharged petrol engine. Acting on signals from th...
View full detailsParts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026