Range Rover Evoque Parts

Fuel Pump Drive Control module within the fuel delivery system, governing operation of the in-tank fuel pump. The module receives a demand signal ...

Coolant Degas Separator, part of the engine cooling circuit on 2.0L Ingenium (AJ200) petrol applications. The degas separator removes entrained ai...

Purge Control Valve - evaporative emission (EVAP) control system. The valve sits in the line between the activated carbon canister and the engine ...

Balance Shaft - counterweighted shaft forming part of the engine balancer assembly in the lower block. Driven from the crankshaft and running at t...

Drive Belt Tensioner - automatic tensioner for the front-end accessory drive on the AJ20 Ingenium petrol engine range. A spring-loaded pivoting ar...

Tyre Pressure Sensor - wheel-mounted pressure and temperature sensor for the Tyre Pressure Monitoring System (TPMS). Mounted at the valve position...

Tyre Pressure Sensor - wheel-mounted sensor forming part of the Tyre Pressure Monitoring System (TPMS). The sensor is fitted at the valve position...

Knock Sensor for the engine management system, mounted on the rear face of the cylinder block. Petrol applications only - Ingenium AJ200P, AJ20P an...

Glow Plug Control Unit - the switching and control module of the diesel pre-heat system, wired between the battery supply and the glow plugs. The ...

Oxygen Sensor (lambda sensor) for the lower, post-catalyst position in the exhaust gas sensing circuit, mounted in the exhaust front pipe at the ca...

Tailgate Latch is the closure latch of the tailgate / luggage compartment lock controls. It engages the body-mounted striker to hold the tailgate ...

Idler Pulley for the accessory drive belt system, mounted on the front of the engine within the auxiliary belt run. The idler pulley drives nothin...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Front Crankshaft Oil Seal - radial lip seal in the cylinder block and front cover assembly, sealing the crankshaft nose where it passes through the...

Wheel Cover for the road wheel. The cover fits over the wheel to give a finished appearance and shield the wheel face from road dirt and brake dus...

Wheel Cover set, fitted over the road wheels. The covers clip over the wheels to give a finished appearance and shield the wheel face from road di...

Timing Chain Tensioner for the 2.0L Ingenium petrol engine (AJ200P). Maintains running tension on the timing chain, taking up slack to keep valve ...

Solenoid Switch for the centre console switch pack, serving as the engine start-stop control. Mounted in the console and facia switchgear, it sign...

Fuel Filler Restrictor for diesel vehicles, fitted inside the fuel filler neck as part of the fuel tank and filler assembly. It forms a physical b...

Trim Clip that secures interior and exterior trim panels, door finishers and mouldings to the body. The clip locates in a pre-formed panel apertur...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Cap - Filler

Valve - Control

Turbocharger - exhaust gas driven turbocharger for the 2.0L I4 Ingenium diesel engine, forming the boost stage of the air induction and exhaust sys...

Screw and Washer - M5 x 20 is a self-tapping fastener with a captive washer, an M5 thread, 20 mm length and a hex head. It secures body panels, sp...

Relay Black 2A 4 Pin

Dust Cap for a brake bleed nipple. This small protective cover fits over the bleed screw on a brake caliper or wheel cylinder. It keeps dirt and m...

Metal Name Plate is an exterior badge fitted to the bodywork. It mounts to the body panel as a model or trim identifier and forms part of the vehic...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Brake Fluid - DOT 4 low-viscosity hydraulic brake fluid, supplied in a 1 litre container. It transmits pedal pressure through the hydraulic brakin...

Retaining Clip - a push-fit fastener used to secure exterior and interior trim mouldings and finishers to the body. The clip pushes into a locatin...

Body Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...