Range Rover Evoque Parts

Exhaust Gas Pressure Sensor for the diesel particulate filter (DPF) circuit on the 2.0L I4 AJ200D diesel engine. The sensor measures exhaust gas p...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Cylinder Head Bolt securing the cylinder head to the cylinder block on the 2.0L 16V Ti-VCT turbocharged petrol engine. The bolt clamps the head, h...

Exhaust Gas Pressure Sensor mounted in the front pipe / catalyst section of the exhaust system. The sensor measures exhaust gas pressure and repor...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Bolt used in the front brake disc and caliper assembly. This is a securing fastener within the front braking installation.

Front Brake Pad Wear Sensor monitors friction-material thickness at the front axle. As the brake pads approach their wear limit, the sensor circuit...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Emission Gasket for the crankcase cover, part of the crankcase ventilation and emission-control system on the 2.0L AJ200/AJ20D4 four-cylinder diese...

O-Ring sealing the variable valve timing (VVT) solenoid cover. Seals the VVT solenoid cover within the engine timing gear, preventing oil leakage ...

Guide - Timing Chain

Wind Deflectors - Front - Evoque 3DR

Wind Deflectors - Set of 4 - 5DR Evoque

Performance Air Filter - Evoque

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

Accessory Drive Belt for the engine accessory (ancillary) drive on 2.0L GTDi and second-generation 2.0L turbocharged petrol engines. The belt is d...

Suspension arm bush for the rear position of the front lower suspension arm (wishbone), in the front strut suspension assembly. The bush presses i...

Ball Joint

Ball Joint Fitting Kit

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Suspension arm bush for the front lower suspension arm (wishbone) in the front strut suspension assembly. The bush presses into the inboard eye of...

Rear Wheel Hub Bearing from the rear hub and bearing assembly, supplied as a sealed unit. The hub bolts to the rear suspension knuckle and carries...

Tie Rod from the steering linkage, running between the steering rack and the steering knuckle. It transmits rack travel to the hub carrier to stee...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Fuel Filler Cap for unleaded petrol applications, sealing the fuel tank filler neck. The cap closes the filler neck and keeps the tank sealed agai...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Drive Shaft Boot Kit - Outer Constant Velocity Joint - Front, part of the front axle drive shaft assembly. The boot seals the outer constant veloc...

Exhaust Manifold Fixing Spacer - a fixing component within the exhaust manifold mounting arrangement of the 2.2L CR DI 16V four-cylinder diesel eng...

Drive Chain Idler - timing gear idler sprocket for the 2.0L four-cylinder Ingenium engine family (AJ200 / AJ20 series, petrol and diesel). The idl...

Engine Mounting Bolt, M14 x 65mm, used in the engine mounting assembly. The bolt secures the engine mounting to its bracket. It carries the static...

O-Ring for the high-pressure diesel fuel injection pump. The ring seals the joint between the pump body and its mounting face on the engine, preve...

DEF Injector Refit Kit

Ball Stud - Tailgate Strut - the ball pivot that a tailgate (luggage compartment door) gas strut socket clips onto. It threads into the body apert...

Front Crankshaft Oil Seal for the Ingenium engine family, sealing the crankshaft nose where it passes through the front cover. The seal runs on th...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Anti-Roll Bar Link - Front, the connecting link between the front anti-roll bar end and the suspension strut in the front suspension assembly. The...

Front Brake Pad Wear Sensor for the front axle brake assembly, part of the brake pad wear warning circuit. The sensor consists of a wire loop seat...

Rear Crankshaft Oil Seal and Retainer forms the oil-tight closure at the flywheel end of the cylinder block, within the Cylinder Block and Cranksha...

Front Brake Pad Wear Sensor Wire from the front brake pad wear warning circuit. The sensor wire is routed into a slot in the front brake pad frict...

Inlet valve stem seal for the cylinder head valve train. The seal is pressed onto the inlet valve guide boss and wipes the valve stem as it recipr...