Range Rover Evoque Parts

Ceramic Glow Plug - cold-start heating element from the diesel pre-heat system, threaded into the cylinder head with the tip projecting into the co...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Cylinder Head Bolt for Ingenium petrol engines (1.5L AJ20P3, 2.0L AJ200 / AJ20P4, 3.0L AJ20P6 / AJ22P6). The bolt clamps the cylinder head to the ...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Nut used in exterior body panel and trim fixings. Secures body components such as the luggage compartment door finisher, radiator grille and bumpe...

MAP Sensor is the manifold absolute pressure and charge-air temperature sensor mounted in the inlet manifold. It reports intake manifold pressure ...

Adhesive and Sealer is a glass bonding adhesive and sealer used to seat and seal fixed automotive glazing to the body. It bonds and seals the wind...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Valve Rocker Arm for the cylinder head valvetrain. It transfers camshaft lift to the valve, actuating the valve as the camshaft rotates. Fitted to...

Valve Stem Seal seals the valve stem where it passes through the valve guide in the cylinder head of Ingenium diesel engines. Fitted over the top ...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Battery - 12V lead-acid battery of flooded, non-spillable construction, for the vehicle low-voltage electrical supply. Non-spillable construction ...

Purge Control Valve - evaporative emission (EVAP) control system. The valve sits in the line between the activated carbon canister and the engine ...

Drive Belt Tensioner - automatic tensioner for the front-end accessory drive on the AJ20 Ingenium petrol engine range. A spring-loaded pivoting ar...

Tyre Pressure Sensor - wheel-mounted pressure and temperature sensor for the Tyre Pressure Monitoring System (TPMS). Mounted at the valve position...

Tyre Pressure Sensor - wheel-mounted sensor forming part of the Tyre Pressure Monitoring System (TPMS). The sensor is fitted at the valve position...

Knock Sensor for the engine management system, mounted on the rear face of the cylinder block. Petrol applications only - Ingenium AJ200P, AJ20P an...

Front Crankshaft Oil Seal - radial lip seal in the cylinder block and front cover assembly, sealing the crankshaft nose where it passes through the...

Wheel Cover for the road wheel. The cover fits over the wheel to give a finished appearance and shield the wheel face from road dirt and brake dus...

Wheel Cover set, fitted over the road wheels. The covers clip over the wheels to give a finished appearance and shield the wheel face from road di...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Cap - Filler

Valve - Control

Screw and Washer - M5 x 20 is a self-tapping fastener with a captive washer, an M5 thread, 20 mm length and a hex head. It secures body panels, sp...

Metal Name Plate is an exterior badge fitted to the bodywork. It mounts to the body panel as a model or trim identifier and forms part of the vehic...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Brake Fluid - DOT 4 low-viscosity hydraulic brake fluid, supplied in a 1 litre container. It transmits pedal pressure through the hydraulic brakin...

Retaining Clip - a fastener for exterior body mouldings and side-step trim. Secures body moulding and side-step trim panels to the bodywork.

Windscreen Washer Pump Grommet seals the washer pump into the windscreen washer fluid reservoir. This rubber grommet fits into the reservoir body ...

Fuel Pump O-Ring Seal, 31mm x 2mm - the sealing ring at the fuel pump / fuel injection pump joint. This O-ring is the only seal at that joint, so ...

Automatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...