Range Rover Sport L494 Parts

Cylinder Head Bolt Kit for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4). Supplied as a set for renewing the cylinder head bolts when the cylin...

Cylinder Head Bolt for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4), securing the cylinder head to the engine block. Supplied as a single bolt...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Diesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...

Timing Chain Tensioner, part of the timing chain drive within the timing cover. It applies controlled load to the timing chain guide to keep the ch...

Fuel Pressure Regulator (fuel pressure control valve) for the diesel high-pressure fuel injection system. Mounted on the high-pressure fuel pump, i...

Idler Pulley for the accessory drive belt system, mounted on the front of the engine within the auxiliary belt run. The idler pulley drives nothin...

Crankshaft Gear, the timing drive gear that mounts on the front of the crankshaft within the timing cover. It drives the timing chain, transferring...

Cylinder Head Gasket for the 2.0L I4 (AJ200 / AJ20D4) diesel engine. It seals the joint between the cylinder head and the engine block, sealing com...

Cylinder Head Gasket for the 2.0L I4 (AJ200 / AJ20D4) diesel engine. It seals the joint between the cylinder head and the engine block, sealing com...

Brake Pad Set - Rear - friction pad axle set for the rear disc brake assembly. The pads locate in the rear caliper carriers and clamp against the ...

Tyre Pressure Sensor - wheel-mounted sensor forming part of the Tyre Pressure Monitoring System (TPMS). The sensor is fitted at the valve position...

Front Crankshaft Oil Seal - radial lip seal in the cylinder block and front cover assembly, sealing the crankshaft nose where it passes through the...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Ignition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Differential Mounting Insulator, a bush-type isolator in the front differential mounting. The insulator locates the front differential to the axle...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Engine Mount Insulator for the engine and transmission mounting system. The insulator is the rubber-and-metal mount that supports the powertrain o...

Anti-Roll Bar Link connects the front anti-roll bar to the suspension, part of the front stabilizer bar assembly. It transfers movement between th...

Piston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...

Piston ring set for the 5.0L V8 AJ133 petrol engine, both naturally aspirated and supercharged, in +0.50 mm oversize. One set covers a single pist...

Piston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...

Brake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...

Drive Belt Idler Pulley - a non-driven guide pulley in the accessory drive belt system of the 3.0L AJ20P6 six-cylinder petrol engine. The idler gu...

Breather Tube forming part of the crankcase ventilation circuit on the 5.0L V8 petrol engine (AJ133). It carries crankcase blow-by gases from the ...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Overflow Container Cap for the cooling system expansion (overflow) reservoir. The cap seals the coolant expansion tank and maintains system pressu...

Brake Pad Set - Rear - friction pad axle set for the rear disc brake assembly. The pads locate in the rear caliper carriers and clamp against the ...

Final Drive Lubricant - a fully synthetic 75W-90 gear oil meeting API GL5, supplied in a 4 litre pack. Specified for the front and rear final driv...

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Cylinder Head Gasket sealing the cylinder head to the engine block. Fitted to the 2.0L four-cylinder AJ200 (Ingenium) petrol engine, including PHE...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Spark Plug Aperture Gasket seals the spark plug aperture in the cylinder head cover on the left hand cylinder bank. It closes the joint between th...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Chain - Timing

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

O-Ring seals the variable valve timing (VVT) solenoid within the timing gear and sprocket assembly. It maintains an oil-tight joint between the VV...