Range Rover Sport L494 Parts

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Starter Motor - the cranking motor of the engine electrical system, mounted at the engine-to-transmission bellhousing. Its pinion engages the flyw...

Diff oil seal

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Stud

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Air Filter element for the engine air cleaner assembly. The filter sits inside the air cleaner housing and cleans the intake air before it passes ...

Telematics Control Unit Backup Battery, a lithium-ion cell that supplies the Telematics Control Unit (TCU) when the main vehicle battery is disconn...

Suspension Arm Nut - M16 flanged nut used on the rear suspension. It secures the lateral and lower arm pivot bolts where they pass through the sus...

Self-Tapping Screw and Washer - a 5 x 20mm self-tapping screw with a captive washer, used as a bumper and grille fixing. It secures the radiator g...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Brake Caliper and Actuator - LH for the rear disc brake assembly, supplied complete with its electronic parking brake (EPB) actuator. The caliper h...

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Rear Crankshaft Oil Seal for the 2.0L AJ200-series four-cylinder engine, in both petrol and diesel applications. Seals the rear of the crankshaft ...

Exhaust Gas Temperature Sensor measures the temperature of the exhaust stream within the diesel exhaust and emissions system. It reports to the en...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

EGT Sensor Exhaust gas temperature sensor in the exhaust and emissions aftertreatment system of the 3.0L V6 diesel engine. It measures exhaust gas...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Trim Clip - push-type retainer used to secure exterior trim, body mouldings, bumper covers and splash shields to the body structure. The clip is p...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Control Module Bracket for the adaptive cruise control distance sensor assembly. This mounting bracket secures the distance sensor to the vehicle ...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Front Radius Arm - LH is a suspension linkage in the front suspension assembly. It connects the front subframe to the wheel knuckle and controls th...

Front Radius Arm - RH is a suspension linkage in the front suspension assembly. It connects the front subframe to the wheel knuckle and controls th...

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

Wheel Hub Assembly for the front and rear axle knuckle assembly. This wheel hub assembly mounts to the steering or rear knuckle and houses the whe...