Range Rover Sport L494 Parts

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Sealing Washer for the fuel injector, part of the diesel fuel injection system. The washer seats between the base of the injector and its bore in ...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Water Outlet Connection - lower coolant outlet housing in the engine cooling circuit of the 4.4L TDV8 diesel engine. It bolts to the engine and di...

Exhaust Gas Temperature Sensor measures the temperature of the exhaust stream within the diesel exhaust and emissions system. It reports to the en...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Brake Caliper Piston for the rear hydraulic disc brake assembly. The piston sits within the caliper bore and transfers hydraulic pressure from the...

Front Brake Caliper Pin Kit covering both front calipers (left and right). The kit supplies the guide pin hardware required when servicing the fro...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Radiator tank assembly (Use Cap PCD000090/PCD500030)

Lower Rear Knuckle Suspension Bush for the rear suspension. This bush fits the lower mounting of the rear knuckle (wheel carrier), forming the comp...

Parking Sensor is an ultrasonic sensor for the Park Distance Control (parking aid) system. Mounted in the bumper, it emits and receives ultrasonic...

Transmission Oil Pan & Filter Kit - the lower fluid pan for the ZF 8HP70 8-speed automatic transmission, incorporating an integrated fluid filt...

Headlamp Washer Pump

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Sump Gasket sealing the oil pan (sump) to the cylinder block. Forms the oil-tight joint between the sump and the engine block, retaining engine oi...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Service PCV Kit

Exhaust Valve for the cylinder head of the 5.0L AJ133 V8 petrol engine. The valve opens to release spent combustion gases from the cylinder into t...

Air Duct - Inlet Manifold Connector in the charge-air induction system of the 4.4L V8 diesel. The connector joins the charge-air ducting to the in...

Water Outlet Tube in the engine cooling system, forming a rigid section of the coolant circuit on the outlet side. Fitted to supercharged petrol e...

Timing Chain Guide for the primary timing chain, fitted on the right-hand side of the timing drive. It locates and supports the chain along its ru...

Timing Chain Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing chain bears...

Water Inlet Tube in the engine cooling system, forming a rigid section of the coolant circuit on the inlet side. Fitted to supercharged petrol eng...

Water Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...

Water Outlet Connection sits at the engine coolant outlet within the cooling circuit, directing coolant from the engine into the connected hoses an...

Gasket - Throttle

Inlet Manifold Gasket for the right-hand cylinder bank, sealing the inlet manifold to the cylinder head. Seals the joint between the inlet manifol...

Inlet Manifold Gasket for the left-hand cylinder bank, sealing the inlet manifold to the cylinder head. Seals the joint between the inlet manifold...

Fuel Injector Pipe Clamp for the high-pressure fuel injection system of the 3.0L V6 and 4.4L V8 (SDV8) diesel engines. The clamp secures a high-pr...

Oil Cooler Tube carries engine oil through the oil cooler circuit. The tube connects the engine oil system to the oil cooler, routing oil to be co...

O-ring for the variable valve timing (VVT) solenoid, part of the timing gear assembly at the front of the engine. The solenoid meters oil flow to ...

Inlet Manifold Gasket for the left-hand cylinder bank of the 5.0 litre V8 petrol engine (AJ133). It seals the joint between the inlet manifold and ...

Vacuum Pump Seal - sealing ring between the engine-driven vacuum pump and its mounting face on the engine, forming part of the brake servo vacuum c...

Connector

O-Ring - Radiator Hose

Intercooler to Inlet Manifold Gasket from the charge air induction system of the supercharged 5.0L V8 petrol engine (AJ133). The supercharger and ...

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...