for Discounts / VAT
for Discounts & Correct VAT
Replacement parts for the Range Rover Velar L560, built at Solihull from 2017 on the JLR iQ[Al] aluminium platform. Covers all Ingenium diesel and petrol variants, MHEV, PHEV, and ZF 8-speed automatic configurations.
Ignition Coil for the engine ignition system. It steps up battery voltage to the high voltage needed to fire the spark plug and is mounted directly...
View full detailsLocking Fuel Cap seals and secures the fuel filler neck on diesel applications. The lockable cap deters fuel theft and tampering while sealing the...
View full detailsTiming Chain - Lower is the lower (primary) chain of the timing drive on the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4, including t...
View full detailsBrake Caliper Guide Pin Kit for a floating (sliding) brake caliper. The guide pins locate the caliper body on its carrier bracket and let it slide ...
View full detailsFuel Pump Drive Sprocket is a timing-drive gear in the timing gear train of the 2.0L Ingenium diesel engine (AJ200D / AJ20D4). Driven by the timin...
View full detailsPiston - 0.50 mm Oversize for the 2.0-litre Ingenium (AJ200D / 204DTD) diesel engine. An engine-rebuild piston machined 0.50 mm over the standard ...
View full detailsSolenoid Switch for the centre console switch pack, serving as the engine start-stop control. Mounted in the console and facia switchgear, it sign...
View full detailsTiming Chain Tensioner - hydraulic tensioner in the timing chain drive of the 2.0L Ingenium four-cylinder turbo diesel (AJ200D / AJ20D4). The tens...
View full detailsTailgate Latch is the closure latch of the tailgate / luggage compartment lock controls. It engages the body-mounted striker to hold the tailgate ...
View full detailsTensioner - Timing Belt
Timing Chain - Secondary, Upper is part of the camshaft drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4), including plug-in ...
View full detailsClimate Control Humidity Sensor, an input device for the automatic climate control system. Mounted at the base of the interior rear-view mirror, i...
View full detailsTiming Chain - the primary drive chain that links the crankshaft to the camshafts, synchronising valve timing with piston movement. For the 2.0L I...
View full detailsFuel Pump Drive Sprocket for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4). The sprocket drives the high-pressure fuel pump from the engine's ti...
View full detailsRoad Wheel Nut secures the road wheel to the hub. The nut clamps the wheel against the hub mounting face and must be tightened to the specified to...
View full detailsHood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...
View full detailsHood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...
View full detailsDrive Belt Tensioner - automatic tensioner for the front-end accessory drive on the AJ20 Ingenium petrol engine range. A spring-loaded pivoting ar...
View full detailsElectronic Parking Brake Actuator for the right-hand rear brake caliper, part of the electronic parking brake (EPB) system. The actuator is a self...
View full detailsDrive Belt Tensioner - automatic tensioner for the front-end accessory drive on the AJ20 Ingenium petrol engine range. A spring-loaded pivoting ar...
View full detailsRelay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...
View full detailsElectronic Parking Brake Actuator for the left-hand rear brake caliper, part of the electronic parking brake (EPB) system. The actuator is a self-...
View full detailsCamshaft Sprocket for the timing drive of the Ingenium engine family - the 2.0L and 3.0L diesel and 3.0L petrol units. Mounted on the end of the ca...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsCoolant Degas Separator, part of the engine cooling circuit on 2.0L Ingenium (AJ200) petrol applications. The degas separator removes entrained ai...
View full detailsBalance Shaft - counterweighted shaft forming part of the engine balancer assembly in the lower block. Driven from the crankshaft and running at t...
View full detailsOil Filter Element and Seal
Camshaft Sprocket is a timing-drive gear in the valve train of the 2.0L Ingenium diesel engine (AJ200D). Mounted on the end of the camshaft, it is...
View full detailsCamshaft Sprocket is a timing-drive gear in the valve train of the 2.0L Ingenium diesel engine (AJ200D). Mounted on the end of the camshaft, it is...
View full detailsWater Pump for the 2.0L Ingenium diesel engine (AJ20D4), part of the engine cooling circuit. Belt- or chain-driven from the engine, the pump circu...
View full detailsCamshaft Sprocket forms part of the timing drive assembly, mounting to the end of the camshaft. Driven by the timing chain, it transfers rotation ...
View full detailsWater Pump for the 2.0L Ingenium diesel engine (AJ20D4), part of the engine cooling circuit. Belt- or chain-driven from the engine, the pump circu...
View full detailsWater Pump for the 2.0L Ingenium four-cylinder engine (AJ200), part of the engine cooling circuit. Driven from the engine, the pump circulates coo...
View full detailsCamshaft Sprocket forms part of the timing drive assembly, mounting to the end of the camshaft. Driven by the timing chain, it transfers rotation ...
View full detailsWater Pump for the 2.0L Ingenium four-cylinder engine (AJ200), part of the engine cooling circuit. Driven from the engine, the pump circulates coo...
View full detailsWater Pump for the 2.0L Ingenium diesel engine (AJ20D4), part of the engine cooling circuit. Belt- or chain-driven from the engine, the pump circu...
View full detailsEngine Coolant - antifreeze and corrosion inhibitor fluid for the engine cooling system. The coolant circulates through the engine water jackets, ...
View full detailsFuel Tank Filler Cap for the fuel filler system on petrol and plug-in hybrid (PHEV) applications. Threads onto the filler neck at the top of the f...
View full detailsElectronic Parking Brake Actuator for the rear brake caliper, part of the electronic parking brake (EPB) system. The actuator is a self-contained ...
View full detailsCamshaft Sprocket for the camshaft drive, mounted on the end of the camshaft and driven by the timing chain from the crankshaft. It transmits the d...
View full detailsFuel Injector - high-pressure common-rail injector for the 2.0L AJ21D4 Ingenium diesel, mid power output. The injector is clamped into the cylinde...
View full detailsFuel Injector for the 2.0L I4 Ingenium (AJ200) diesel engine, part of the high-pressure common rail fuel injection system. The injector is clamped...
View full detailsFuel Injector for the 2.0L AJ200 (Ingenium) four-cylinder diesel engine. The injector delivers a metered, high-pressure spray of diesel into the c...
View full detailsPark Assist Camera from the parking aid and surround view system. Captures the video feed used by the parking aid display, passing the image to th...
View full detailsCombined Oil and Vacuum Pump for the 2.0L Ingenium (AJ200) diesel engine. This tandem unit houses the engine oil pump and the vacuum pump in a sing...
View full detailsHigh Voltage Water Heater for plug-in hybrid (PHEV) applications, operating in the high-voltage coolant heating circuit. The unit heats engine coo...
View full detailsTurbocharger for the 2.0L AJ200 / AJ20D4 four-cylinder diesel engine. It sits in the forced-induction circuit between the exhaust manifold and the...
View full detailsTurbocharger for the 2.0L AJ200 / AJ20D4 four-cylinder diesel engine. It sits in the forced-induction circuit between the exhaust manifold and the...
View full detailsThe Velar L560 has been produced with a wider engine range than most single-generation Land Rover models, and correct part fitment depends on knowing your engine code and model year. The pre-facelift range ran from 2017 to 2020 and included the Ingenium D180 and D240 four-cylinder diesels, the twin-turbo D300 and D275 V6 diesels, the P250 and P300 four-cylinder petrols, the P340 and P380 supercharged V6 petrols, and the limited SVAutobiography Dynamic with the 5.0-litre V8. From September 2020, the engine range was revised. The D200 replaced the D180 with mild hybrid assistance, the P400 Ingenium turbocharged inline-six replaced the P380 V6, and the P400e PHEV was introduced, combining a 2.0-litre Ingenium petrol unit with a 106 kW permanent magnet synchronous motor and a 17.1 kWh lithium-ion battery. A mild exterior and infotainment refresh was applied from 2023. Fitment differences exist between pre-facelift, post-September-2020, and post-2023 vehicles, particularly for engine ancillaries, emissions components, and hybrid system parts.
All four-cylinder variants use the ZF 8HP45 eight-speed automatic gearbox. All six-cylinder variants use the heavier-duty ZF 8HP70 unit. Gearbox-related parts must be matched to the correct variant.
Engine specifications and ZF 8HP transmission variant assignments confirmed against ZF Group 8HP-series technical data and JLR engine specifications as documented in the Range Rover Velar L560 launch technical record.
The Velar L560 shares its iQ[Al] D7a aluminium platform with the Jaguar F-Pace, Jaguar XF (X260), and Jaguar XE. This means a number of underbody, suspension geometry, and fastener components are shared across those vehicles. Workshops sourcing parts for the Velar may find that certain subframe components, suspension bushings, and general hardware are catalogued across both JLR and Jaguar parts systems. This does not apply to powertrain-specific or model-specific body parts. Always confirm part numbers against the Velar L560 catalogue before ordering on the basis of platform compatibility alone.
Fitment ConfirmationThe Velar L560's broad engine and drivetrain range means that year-of-manufacture alone is not sufficient to confirm fitment for many parts. The Vehicle Identification Number (VIN) contains the production sequence, engine code, and build specification and is the most reliable way to confirm the correct part for your vehicle. The VIN is located on the windscreen lower edge (driver's side on most LHD markets, passenger's side on RHD markets) and on the vehicle's identification plate in the engine bay. If you are unsure whether a listed part fits your specific Velar, contact Budget Parts with your VIN before ordering.
Related CollectionsFor parts covering other Range Rover generations or the broader Range Rover family, see Range Rover parts.
For Velar-adjacent models built on the same generation platform, the Range Rover Evoque L538 parts collection covers the previous Evoque generation and the Range Rover Sport L494 parts collection covers the Sport generation sharing the same era of Ingenium engine development.
Technical GuidesThe following article from the Budget Parts technical library covers the Velar L560 platform, engines, and ownership considerations relevant to parts selection.
A technical reference covering the iQ[Al] D7a platform, Ingenium engine range, AWD systems, and the service considerations that affect accurate parts selection on the Velar L560.
Range Rover Velar L560 guide →The Range Rover Velar L560 entered production in 2017 and is the only current generation of the Velar. A mild facelift was introduced in 2023, primarily affecting exterior styling and the infotainment system. A second-generation Velar on a new electric-only platform is announced for production from 2027 and is a separate vehicle entirely. Parts on this page cover the L560 generation only, from 2017 to present.
The engine code is stamped on the engine block and is also encoded in your VIN. For diesel variants, the main codes in service are D180 (2017 to 2020), D200 (2020 onwards, MHEV), D240 (2017 to 2020), D300 V6 (2017 to 2020), and D300 Ingenium inline-six (2020 onwards). For petrol variants, the main codes are P250, P300 (2017 to 2020), P340, P380 (2017 to 2020), P400 MHEV (2020 onwards), and P400e PHEV (2020 onwards). Engine-specific parts including timing components, injectors, and turbo ancillaries must be matched to the correct code.
Yes, in part. Both vehicles are built on the JLR iQ[Al] D7a aluminium platform, sharing the same wheelbase of 2,874 mm and common underbody architecture. This means certain suspension geometry components, subframe hardware, and general fasteners are shared across the catalogue. However, powertrain-specific parts, body panels, and model-specific electronics are not interchangeable. Workshops cross-referencing parts between the Velar and F-Pace should always verify against the Velar L560 part number before ordering.
All Velar L560 variants use a ZF 8-speed automatic transmission. Four-cylinder engines (diesel and petrol) are paired with the ZF 8HP45 unit. Six-cylinder engines, including the P380, P400, D300 V6, and D300 I6, are paired with the heavier-duty ZF 8HP70 unit. Gearbox-related parts, including oil, filter kits, solenoids, and sensors, must be matched to the correct 8HP variant for your engine.
Genuine parts carry the official Land Rover part number and are manufactured to JLR specification. OEM parts are produced by the same manufacturer that supplied the component to JLR originally, meeting the same specification without the Land Rover branding. Aftermarket parts are independently manufactured and are suitable for wear items and general maintenance where exact OEM specification is not required. All three tiers are available through Budget Parts for the Velar L560.
Use your VIN. The 17-character VIN encodes your engine code, production year, and build specification and is the most reliable way to confirm fitment before ordering. The VIN is located on the lower edge of the windscreen (driver's side on most LHD markets, passenger's side on RHD markets) and on the identification plate in the engine bay. If you need help confirming fitment, contact Budget Parts with your VIN and the part reference you are considering.
Yes. The collection includes parts relevant to the P400e PHEV (introduced September 2020) and D200 and P400 MHEV variants. These include hybrid system ancillaries, AdBlue components for diesel MHEV variants, and Ingenium engine parts common to the hybrid-equipped models. Specific high-voltage battery components are not included in this collection. Contact Budget Parts if you are sourcing parts for a specific PHEV or MHEV repair and are unsure whether a listed part applies to your variant.