Range Rover Velar Parts L560

O-Ring is a sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder AJ200 diesel engine. It seals a joint in th...

Radiator Ventilation Hose vents the cooling system at the radiator, within the cooling system pipes and hoses. It allows air to bleed from the coo...

Guide - Timing Chain

Radiator Ventilation Hose vents the cooling system at the radiator, within the cooling system pipes and hoses. It allows air to bleed from the coo...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Flywheel Bolt - hex head fastener that secures the flywheel to the rear crankshaft flange within the engine driveline assembly. Fitted to the 3.0L...

Radiator Hose - Engine Vent Elbow forms the vent connection between the engine and the radiator within the cooling system pipes and hoses. The elb...

Brake Pad Wear Sensor for the front axle brake system. The sensor is routed at the front brake pads and signals the vehicle when the friction mate...

Oil Return Hose - the oil drain hose in the turbocharger lubrication circuit. It returns oil from the turbocharger bearing housing to the sump aft...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...

Anti-Roll Bar Link connects the front anti-roll bar to the suspension within the front suspension assembly. Mounted at the front cross member, it ...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Anti-Roll Bar Link connects the front anti-roll bar to the suspension within the front suspension assembly. Mounted at the front cross member, it ...

Nut used in exterior body panel and trim fixings. Secures body components such as the luggage compartment door finisher, radiator grille and bumpe...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Front Crankshaft Oil Seal located at the front of the cylinder block, on the crankshaft. Seals the crankshaft where it exits the front of the engi...

Radiator Hose - Engine Vent Elbow forms the vent connection between the engine and the radiator within the cooling system pipes and hoses. The elb...

Windscreen Wiper Blade for the front wiper assembly. Clears rain and road spray from the windscreen, mounted to the wiper arm within the wash/wipe...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Brake Pad Wear Wire is the front brake pad wear warning sensor, fitted to the front brake pads within the front disc and caliper assembly. The wir...

Anti-Roll Bar Link connects the rear anti-roll bar to the suspension within the rear suspension assembly. It transfers load between the stabiliser...

Anti-Roll Bar Link connects the anti-roll bar to the suspension within the suspension assembly. It transfers load between the stabiliser bar and t...

Exhaust Valve for the cylinder head of the 5.0L AJ133 V8 petrol engine. The valve opens to release spent combustion gases from the cylinder into t...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Exhaust Gas Recirculation Gasket seals the joint between the EGR cooler and the EGR valve on the right-hand side, maintaining a gas-tight connectio...

Exhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...

Gasket - Exhaust Manifold

Fuse installs within the electrical power distribution system, protecting a circuit against overcurrent by interrupting the supply when the rated c...

Circuit Breaker installs within the electrical power distribution system, protecting a circuit against overcurrent by interrupting the supply when ...

Remote Control Receiver forms part of the anti-theft alarm system, receiving the radio signal transmitted by the remote key fob. It relays the loc...

EGR Valve Gasket seals the exhaust gas recirculation valve to its mating face within the EGR and front exhaust system. Fitted on the left-hand ban...

Gasket seals the exhaust gas recirculation (EGR) valve joint on the left-hand side of the 3.0 V6 diesel (Gen2) engine. It forms a gas-tight seal b...

Clip secures an exterior body moulding to the body panel. It is a retaining clip used in the body moulding assembly, holding a trim moulding in po...

Clip - Body Moulding is a retaining clip that secures exterior body moulding and trim to the bodywork. It holds the moulding against the panel and...

Gasket seals the exhaust gas recirculation (EGR) valve joint on the left-hand side of the 3.0 V6 diesel (Gen2) engine. It forms a gas-tight seal b...

EGR Outlet Gasket seals the outlet joint of the exhaust gas recirculation (EGR) system, where recirculated exhaust gas leaves the EGR valve/cooler ...

Valve Spring Seat is the seat on the cylinder head that locates the base of the valve spring, providing the surface against which the spring is com...

Fuse is a plug-in automotive blade fuse used in the vehicle fuse and relay boxes to protect an electrical circuit. It seats in a standard fuse hol...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...