for Discounts / VAT
for Discounts & Correct VAT
Browse our complete range of Land Rover and Range Rover parts- from OEM-quality replacements to specialist upgrades. Whether you’re restoring a classic Defender, maintaining a Discovery, or tuning a modern Range Rover, our parts selection covers every system: engine, suspension, braking, transmission, and more.
Interior Door Handle for the left-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the latc...
View full detailsCoolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...
View full detailsO-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...
View full detailsFlanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...
View full detailsDrain plug LT77 R380
Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...
View full detailsHub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...
View full detailsCoolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...
View full detailsDrive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...
View full detailsFuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...
View full detailsDrive Belt (V-belt) for the engine accessory drive system, transferring rotation from the crankshaft pulley to a driven accessory. This is a 13 mm...
View full detailsTaper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...
View full detailsGrommet
Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...
View full detailsHigh Note Horn, the high-pitched unit of the vehicle's dual-tone horn system. It sounds together with the low note horn to produce the two-tone au...
View full detailsAlternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...
View full detailsHeadlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...
View full detailsHub Outer Oil Seal Spacer for the listed Land Rover Defender, Discovery 1 and Range Rover Classic hub applications. FRC8227 is the spacer/collar us...
View full detailsCamshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...
View full detailsPower Steering Reservoir
Water reservoir grommet rubber seal
Wheel Centre Cap in a Silver Sparkle finish with the embossed Land Rover logo, fitting the centre bore of the alloy road wheel. It conceals the hub...
View full detailsHigh/Low Lever Gaiter - the flexible boot that seals the transfer box high/low range selector lever where it passes through the centre console. Fi...
View full detailsClutch Release Fork - Heavy-Duty is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch sl...
View full detailsHex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...
View full detailsFront Anti-Roll Bar Bolt secures the front anti-roll bar within the front suspension assembly. It fixes the bar to its mounting, holding it in pos...
View full detailsscrew M5 x 12
Shock Absorber Bush - Rear Upper is the mounting bush at the upper end of the rear shock absorber, where the damper attaches to its body mounting. ...
View full detailsBrake T-Piece - Metric is a three-way junction in the brake hydraulic circuit. It joins three brake pipes at a single union, typically distributin...
View full detailsClutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...
View full detailsBypass Hose forming part of the engine cooling circuit on the 2.5L 300TDi turbo diesel engine. It carries coolant through the bypass route at the ...
View full detailsCoolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...
View full detailsAluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...
View full detailsBrake Pipe Clip - Double
Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...
View full detailsFlange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...
View full detailsOil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...
View full detailsAirflow Meter — the hotwire mass air flow sensor for the V8 EFI engine management system. Mounted in the intake tract between the air filter and t...
View full detailsFlange Screw, M6 x 16mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...
View full detailsRubber Head Plug closing a machined oil-way opening on the 200Tdi 2.5L four-cylinder turbo diesel engine. The rubber plug seals an oil gallery ope...
View full detailsLocking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...
View full detailsGasket for transfer box gearchange lever housing plate LT230 with LT85, LT77, Chrysler 3-speed or ZF 4-speed automatic. Also part of gasket kit RTC...
View full detailsSelector yoke spherical bush
Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...
View full detailsHydraulic Fluid - Rock Oil Power Steering and Active Cornering Fluid, 1 litre. Formulated for power steering systems and Active Cornering Enhanceme...
View full detailsWater Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...
View full detailsShock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...
View full detailsClutch Hose forms part of the clutch hydraulic circuit, carrying fluid between the clutch master cylinder and the slave cylinder. The flexible hos...
View full detailsThis page lists every Land Rover and Range Rover part stocked across our Dutch warehouse network. With the full catalogue in one place, the fastest way to reach the right component is to narrow down by your model or by the system you are working on, using the links below.
Shop by modelParts for Series-derived, Td5, Puma and L663 Defender generations.
Land Rover Defender partsParts spanning Discovery 1 through Discovery 5 and Discovery Sport.
Land Rover Discovery partsParts for every Range Rover line from Classic to the latest generations.
Range Rover partsParts for Freelander 1 and Freelander 2 across petrol and diesel variants.
Land Rover Freelander partsPanels, mounts, fasteners and structural components.
Land Rover chassis and body parts