Land Rover Parts

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

Exhaust Manifold Gasket for the 4.0L and 4.6L EFi V8 petrol engine. This twin-port gasket seals the exhaust manifold-to-cylinder head joint at two...

Water Pump Seal - sealing ring for the coolant pump within the engine cooling circuit. It forms the coolant-tight joint between the pump and its m...

Injector Insulation Pad for the fuel injection system on the Td5 2.5L five-cylinder turbo diesel engine. The pad fits over the electronic unit inj...

Exhaust Valve for the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The valve seals the combustion chamber against the exhaust ...

Flywheel Bolt for the 2.5L Td5 five-cylinder diesel engine with manual gearbox. This bolt secures the flywheel to the rear flange of the crankshaft...

Drive Belt Idler Pulley for the auxiliary (accessory) belt drive of the Td5 2.5L 5-cylinder turbo diesel engine. The pulley mounts above the water...

Seal - Oil Pump

Alternator for the charging system on the V8 EFI petrol engine. Driven by the accessory belt from the crankshaft pulley, the alternator generates ...

Camshaft Position Sensor for the V8 EFI petrol engine management system. Signals camshaft rotation to the engine management ECU, allowing it to id...

Camshaft Position Sensor for the V8 EFI petrol engine management system. Signals camshaft rotation to the engine management ECU, allowing it to id...

Ignition Coil Pack in the engine ignition system, generating the high-tension voltage that fires the spark plugs. Used on the distributorless V8 e...

Piston for the 4.6L V8 EFI petrol engine, high-compression specification, supplied without piston rings. Reciprocates within the cylinder bore, tr...

Piston for the 4.0L V8 EFI petrol engine, supplied without piston rings. Reciprocates within the cylinder bore, transmitting combustion pressure t...

Piston for the 4.0L V8 EFI petrol engine, high-compression specification. Reciprocates within the cylinder bore, transmitting combustion pressure ...

Camshaft for the valvetrain of the 4.0/4.6L V8 petrol engine. Mounted in the cylinder block and driven from the crankshaft, the camshaft lobes act...

Viscous Unit

Viscous Cooling Fan Assembly for the 4.0L and 4.6L V8 petrol engines, part of the engine cooling system. The assembly combines the engine-driven c...

Stepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

Key - Mainshaft

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Module - UN3268

Sun Visor Retainer Clip – the moulded clip the free end of the front sun visor locates into when it is folded up against the headlining. It fits t...

Sunroof Seal for the upper frame of the factory tilt-and-slide sunroof assembly. The seal seats around the upper sunroof frame and bears against t...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Rear Bumper Bracket Clip - a plastic retaining clip used in the rear bumper assembly to secure the bumper bracket to the body. It locates the brac...

Clip for the headlamp washer system. Retains the headlamp washer jet to the bumper.

Rear Panel Applique - the exterior finisher panel that fits across the rear door, incorporating the licence plate bracket and covering the rear doo...

End Cap

Windscreen Washer Jet A heated twin-nozzle washer jet that directs washer fluid onto the windscreen. It seats into the scuttle or bonnet panel and ...

Jet - Windshield Washer

Washer Reservoir Cap closes the filler neck of the windscreen washer reservoir. It seals the reservoir to retain washer fluid and keep dirt and deb...

Headlamp

Washer Bottle The reservoir that stores washer fluid for the windscreen and headlamp wash systems. The dual-wash bottle feeds both the windscreen w...

Wiper Clip A retaining clip within the windscreen wiper assembly that secures the wiper blade to the wiper arm, holding the blade in place on the arm.

Cap

Wiper Motor The electric motor that drives the front windscreen wiper linkage, for right-hand drive (RHD) applications. It converts electrical driv...

Windscreen Wiper Arm is a front wiper arm for right-hand drive (RHD) applications, suitable for either side of the windscreen. It fastens to the w...

Finisher LH

Trim - D Pillar

D-Pillar Trim An exterior bodyside finisher for the D-post, the rearmost pillar of the body. It fits over the D-pillar to provide a finished exteri...

Rear Tonneau Finisher - the textured-black rear quarter moulding that trims the rear body panel on the left-hand side. This exterior finisher fits...