Land Rover Parts

Injector Clamp Bolt for the Td5 2.5L 5-cylinder turbo diesel engine. It secures the injector clamp to the cylinder head, holding the fuel injector ...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Bumper Lamp rear right-hand assembly, part of the rear bumper lighting cluster. The unit combines the rear fog lamp and direction indicator in a s...

Fir Tree Fastener push-in fixing in grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fir-tree...

Oil Pump Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the oil pump to its mounting on the engine. It clamps the pump body agains...

Fuel Return Check Valve is a non-return valve fitted in the fuel return circuit of the Td5 fuel system. It permits fuel flow in one direction only...

Headlamp Fixing Kit for headlamps with manual beam adjustment. The kit renews the fixings and adjusters that retain the headlamp unit and set its ...

Drive Belt Idler Pulley for the auxiliary (accessory) belt drive of the Td5 2.5L 5-cylinder turbo diesel engine. The pulley mounts above the water...

Speedo cable oil seal retainer plate

O-Ring for the power steering hydraulic circuit. The ring seats at a hydraulic union in the steering system, sealing the joint against the pressur...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Window Regulator Motor - RH is the electric drive motor for the right-hand window regulator assembly. It mounts directly to the window regulator m...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Alternator, 120A, for the 2.5L Td5 diesel - the charging-system unit that supplies the vehicle's electrical power and recharges the battery. Belt-...

Ignition Lead Set - a complete set of numbered 8mm HT (high-tension) leads for the 4.0 and 4.6 V8 petrol engine. The leads carry the high-voltage ...

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Head gasket set 3.9 EFI MA on

O-Ring for the power steering hydraulic circuit, sealing a connection within the pressurised steering fluid system. This is the brown, thick-secti...

Rear Brake Caliper Carrier for the rear disc brake assembly. The carrier bolts to the rear hub and holds the brake pads, locating the caliper over ...

Hex-head bolt, 3/8" UNC thread, 1-1/8" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and so...

Stud M8 x 25

Rear Bumper Lamp from the rear lighting assembly - the right-hand (RH) unit mounted in the rear bumper. The combined lamp carries the reversing li...

Window Switch

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Bumper Lamp Assembly, left-hand side, part of the rear bumper lighting cluster. A combined lamp unit with a red lens section serving the stop and ...

Fuel block connector assembly (with hose) TD5

Crankshaft Damper mounts on the nose of the crankshaft and forms part of the front-end accessory drive on the Td5 2.5L 5-cylinder turbo diesel. It...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Nut - an M10 self-locking hex nut used in the exhaust system to secure flanged joint and manifold connections. The self-locking feature resists lo...

Oil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...

Power steering pump

Drag link steering LHD D2

Bleed Screw - Blue Anodised Aluminium for the coolant bleed point on Td5 engines. The screw seats in the bleed port on the top coolant hose and is...

Oil seal

Intermediate Exhaust Pipe in stainless steel, forming the centre section of the Td5 exhaust system. This is a straight-through link pipe fitted in...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Shock Absorber Bush for the front lower shock absorber mounting within the suspension damper assembly. The bush fits at the lower eye of the front...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Head Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the joint between the cylinder head and the cylinder block. It seals the comb...

Air flow meter TD5 replacement