Land Rover Parts

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Hex Nut - M14 for use in Land Rover suspension and general fastener applications. A metric M14 standard hexagonal nut for use in axle, suspension,...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Rear Lower Suspension Arm (Right-Hand) is a lower control arm in the rear independent suspension. It locates the rear hub carrier to the chassis s...

Door Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Air Filter - the air cleaner element for the engine air intake system. The element sits within the air cleaner housing and filters incoming air be...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Fitment: All Models 2.7 TDV6 To (V) 6A999999 2.7L TDV6 diesel models to (VIN) 6A999999

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Oil Filter for the 2.7L TDV6 diesel engine, part of the engine lubrication circuit. A paper-element filter that removes wear particles and contami...

Brake hose assy. fr. LH D3, D4

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Lower Arm Bush is a pivot bush for the front lower suspension arm. It mounts the lower control arm to the chassis, allowing the arm to articulate ...

Parking Brake Actuator Repair Gears - replacement drive gears for the electric parking brake (EPB) actuator module. Replaces the internal gears th...

Front Lower Suspension Arm, right-hand side, for vehicles equipped with Roll Stability Control (RSC). Part of the independent front suspension ass...

Lower Rear Knuckle Suspension Bush for the rear suspension. This bush fits the lower mounting of the rear knuckle (wheel carrier), forming the comp...

Parking Brake Actuator Repair Kit - the internal service parts for the electric parking brake (EPB) actuator module. Replaces the worn drive gears...

Special bolt

Intercooler to Inlet Manifold Hose for the 300TDi 2.5L turbocharged diesel engine intercooler circuit on the Discovery 1 and Range Rover Classic. ...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

The OEM Service Kit is designed for Discovery 3 (4.4 V8 EFI Petrol) and Range Rover Sport (4.2/4.4 V8 Petrol) models. This kit includes all the ess...

Clutch Alignment Tool is a double-ended workshop tool for centring the clutch on manual transmission applications. During installation the tool ho...

Discovery 3 Haynes Manual

Gearbox Sump Gasket for the automatic transmission oil pan. This is the gasket only - it seals the oil pan and oil screen to the gearbox case. For...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Crankshaft Trigger Wheel Installer - a service tool for fitting the crankshaft trigger (reluctor) wheel to the crankshaft on the TDV6 engine. It l...

Screw - M5 x 20 mm fixing screw used to secure the front and rear wheel arch mouldings and the adjoining rear bumper section to the bodywork. A bo...

Ride Height Sensor is a rotary position sensor in the electronic air suspension system, mounted at the front right-hand corner. It links to the su...

Rear Window Heated Switch

Raised Air Intake relocating the engine air intake to an elevated position at the A-pillar, drawing clean air from above the standard bonnet-level ...

Swing Away Spare Wheel Carrier for the Discovery 3 and 4, providing an external spare wheel mounting position at the rear of the vehicle. The carr...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Brake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...

Bolt for the rear suspension assembly. This fastener is used in the rear cross member and stabilizer bar assembly, and in the rear knuckle and low...

Eccentric Washer - an adjusting washer used at the front suspension arm pivot mounting. The offset (eccentric) hole allows the arm's pivot bolt po...

Anti Roll Bar Link - Rear connecting the rear anti-roll bar to the suspension trailing arm. This drop link bolts between the rear anti-roll bar an...

Ball Joint - Suspension Arm is the lower ball joint in the front suspension, fitted at the outer end of the lower wishbone and connecting it to the...

Secondary Drive Belt Tensioner for the auxiliary belt drive of the 4.4L AJ-V8 petrol engine. These V8 engines use a two-belt accessory drive; this...

Hose Intercooler - TDV6

Pollen Filter for the cabin ventilation system, installed in the HVAC air intake housing. It traps pollen, dust and airborne particulates from the...

Brake Caliper Piston for the rear hydraulic disc brake assembly. The piston sits within the caliper bore and transfers hydraulic pressure from the...

Rear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...

Suspension Arm - front lower control arm (wishbone) for the right-hand side, fitted to models with air suspension. It connects the chassis to the l...

Exhaust Manifold Nut is an M8 flanged hex nut that secures the exhaust manifold and turbocharger mounting flanges to the cylinder head. The copper...