Land Rover Parts

Rear Subframe Angle Bracket for the rear chassis and subframe assembly, in the High Capacity Pick Up (HCPU) configuration. The angled bracket prov...

Bearing Holder - front bearing housing within the Front Axle Drive Shaft assembly. The holder carries and retains the front support bearing of the...

Front Axle Drive Shaft transmits torque from the front differential output to the front wheel hub, forming part of the front driveline assembly. T...

Transfer Case Support bracket that carries the intermediate bearing of the front axle drive shaft where the shaft runs from the transfer case. It ...

NOx Trap Temperature Sensor is an exhaust gas temperature sensor within the diesel exhaust aftertreatment system, mounted in the exhaust stream at ...

Bolt - Hexagon Head used in engine and interior fascia assembly applications. This hexagon head fastener is used in the EGR system assembly and in...

Rear Bumper Reflector, left-hand side - a passive (non-illuminated) retroreflector set into the rear bumper. It reflects the headlamps of followin...

Rear Bumper Reflector for the right-hand position of the rear bumper. This passive retroreflector fits into the designated aperture in the rear bu...

Fuel Cap - Freelander

Cable Assembly

Bulb and holder GENUINE LR Discovery 2: for instrument cluster

Front Side Lamp forms part of the exterior lighting system, providing front position and side marker illumination. Mounted at the front of the veh...

Rear Right-Hand Ride Height Sensor within the air suspension and headlamp levelling systems. This rotary position sensor mounts to the right-hand ...

Plastic Rivet used to secure interior trim and body panels in position. Push-fit fastener that replaces a lost or damaged original rivet.

Retainer Clip for the headlamp and front end carrier assembly, quarter-turn type. The clip locks with a quarter turn to secure the headlamp and fr...

Thrust Washer

Reverse Selector Fork for the Land Rover Series IIA and Series III 4-speed main gearbox, Suffix A build. This fork engages and disengages reverse ...

Oil Filter - element-type (cartridge) oil filter for the engine oil filter housing on the 3.6L TDV8 diesel (Lion) engine. The replaceable filter e...

Oil Filter for the 2.7L TDV6 diesel engine, part of the engine lubrication circuit. A paper-element filter that removes wear particles and contami...

Blanking Plate - moulded plug that closes an unused switch aperture in the facia or switch console. Where a vehicle is built without an optional s...

Rear Lamp Assembly, left-hand side - the body-mounted section of the rear light cluster (the in-body lamp, as distinct from the separate tailgate-m...

Light Guard - Rear Upper Protective guard for the upper rear lamp cluster, forming part of the exterior lighting protection assembly. The guard mo...

Air Filter for the engine air intake system. The element installs in the air cleaner housing and traps airborne dust and debris from the incoming a...

Snap Ring is a retaining ring that seats into a machined groove to locate a component on a shaft or within a bore, holding it against axial movement.

Inlet Manifold - LH

Oil Filter for the 2.2L Puma turbo diesel engine. The filter removes metal particles, carbon and other contaminants from the circulating engine oi...

Fuel Filter Element - the in-line fuel filter element on the front fuel supply lines. It removes particulate contamination from the diesel supply ...

Seat Belt and Retractor assembly for the occupant restraint system. It combines the seat belt webbing with the inertia-reel retractor, which permit...

Exhaust Manifold Stud secures the exhaust manifold to the cylinder head, part of the exhaust manifold mounting hardware. This is an M10 stud, thre...

Oil Filter for the engine lubrication system of the 4.4L V8 petrol (EFI) and 4.2L V8 supercharged petrol engines. The filter removes wear particle...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...

Air Filter is the air cleaner filter element for the engine intake system. It sits within the air cleaner housing upstream of the intake tract, re...

Stud for the timing cover (front cover) of the 2.5L 4-cylinder diesel engine. The stud locates and clamps the front cover to the cylinder block, p...

O-Ring seals the joint between the sump and the ladder-frame assembly on the 2.5L 200TDi diesel engine.

Parking Aid Sensor - ultrasonic transducer for the Parking Distance Control (PDC) system, mounted through the rear bumper cover. Straight-bodied ty...

Contact Set for Elec. Fuel Pump

Bulkhead Seal for the dash ventilation aperture on Defender models without air conditioning. This rubber seal fits between the dash ventilator ass...

Console Switch Bezel Ring is the trim surround for the floor switch assembly on the centre console. It frames the console switch panel, locating a...

Hill Descent Control Switch is the facia-mounted switch that engages the Hill Descent Control (HDC) system. When activated at low speed, HDC uses ...

Rear lamp assembly OEM LH

Strap fuel tank Defender 110 TD5/TD4

Alloy Wheel - a 7J x 16" five-spoke cast alloy road wheel with a dual (two-tone) finish. The spoke face carries embossed lettering as a styling de...

Housing Rear Axle Lion Diesel 2.7 V6

Rear Seat Back Adjusting Handle - the release lever on the rear seat frame assembly. The handle operates the seat back latch, releasing the backre...