Land Rover Parts

Spring bonnet pull cable return

Lamp side repeater RRC

Fuel Lift Pump for the low-pressure fuel supply circuit of the 2.5L 300TDi turbo diesel engine. This engine-mounted mechanical diaphragm pump draw...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

T-Piece is a three-way connector in the windscreen washer fluid circuit. It joins the washer hose into two branches, distributing fluid from the p...

Heater Hose - Outlet - V8 forms part of the heater coolant circuit on V8 petrol applications. It carries coolant from the heater matrix outlet bac...

Clip

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Dipstick tube O-ring 200 & 300TDi, TD5

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Door Glass Channel - Lift - Front - D1/RRC

Crankcase breather T-piece with restrictor V8 EFI

Headlamp Bezel - black finish. The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing the hea...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Water Pump for the 200TDi 2.5L turbo diesel engine, operating in the engine cooling circuit. Belt-driven from the crankshaft, the pump circulates ...

Track Rod End with a right-hand thread, forming part of the steering linkage. The track rod end is the articulating ball joint that connects the t...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Track Rod End with right-hand thread, fitting at the outer end of the track rod within the steering linkage on the Defender, Discovery 1, and Range...

Oil seal

Drain plug

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 300 TDi 2.5L diesel engine. It forms a coolant-tight joint...

Strap

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Lower Arm Link – Rear is a rear suspension locating link connecting the rear axle to the chassis on coil-sprung suspension. It locates the axle fo...

Anti-Squeal Shim is a thin damping shim for the rear disc brake assembly. It fits between the brake pad backing plate and the caliper piston, isol...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

O-Ring for the speedometer drive spindle on the LT230 transfer gearbox. Seals the spindle housing where the speedometer drive take-off enters the ...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Anti-Rattle Spring for the front disc-brake caliper. It holds the brake pads under light tension inside the caliper, taking up free play so the pad...

Rear Propshaft Rubber Coupling - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while ab...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Ignition heater plug timer glow plug relay

Oil Filter for the engine lubrication system of the early V8 petrol engine. The filter removes metallic particles, carbon and other contaminants f...

Oil seal 12.5mm OEM

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...

Side Repeater Lamp

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...