Land Rover Parts

Lower Spring Seat locates the base of the coil spring in the suspension. It provides the lower bearing surface on which the road spring rests, pos...

Rear brake shield RH

Viscous Fan Coupling - temperature-sensitive drive coupling between the water pump drive and the engine cooling fan. It modulates fan speed with u...

Radiator is the main engine cooling radiator with an aluminium core, serving the front of the engine cooling circuit. Mounted ahead of the engine ...

Single Pipe Clip, a routing clip that retains a single pipe or line against the chassis or body. It holds fuel, evaporative-loss or brake pipework...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Wheel Centre Cap in a Silver Sparkle finish with the embossed Land Rover logo, fitting the centre bore of the alloy road wheel. It conceals the hub...

Level plug R380

Hose pump to box

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Cylinder Head Bolt for the 300TDi 2.5L turbo diesel engine, part of the cylinder head-to-block assembly. The bolt clamps the cylinder head onto th...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...

Crankshaft Thrust Washer Pair for the 4-cylinder engine, including the 200 TDi and 300 TDi diesels. The thrust washers sit either side of the centr...

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Exhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...

Radius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...

Flange Bolt - M8 x 85mm hex bolt with an integrated flange beneath the head. The flange spreads the clamping load across a wider bearing surface a...

Cylinder Head Bolt, M10 x 117 mm for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It secures the cylinder head to the eng...

Radiator Top Hose is the upper coolant hose in the engine cooling circuit. It carries hot coolant from the engine thermostat housing to the top of ...

A/C Drive Belt drives the air-conditioning compressor on the 2.5L 300TDi diesel. Run from the crankshaft pulley, it transmits drive to the air-con...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Exhaust Olive is a tapered sealing ring used at the exhaust system's pipe joints. It seats between two pipe sections at a compression joint, formi...

Alternator 300TDi (with pulley)

Aerial with cable Defender

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Brake Pipe Clip (double) used to route and secure rigid brake pipes within the braking hydraulic system. The double form retains two brake pipes s...

Fir Tree Clip push-in fastener used to secure interior door casings and trim panels to the body shell. The barbed fir-tree profile is pushed into ...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Bolt 10.9 M12 x 100

Sealing Washer for the carburettor choke switch on petrol engine applications. Fitted at the choke switch, it seals the joint at the fitting to pr...

Brake Disc Splash Shield - Front, RH, mounted behind the right-hand front brake disc. The shield sits between the stub axle / hub and the brake di...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Handbrake Adjuster Repair Kit for the cable-operated transmission drum handbrake. The kit renews the adjuster mechanism of the drum brake mounted ...

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

Edge Clip a body fixing that secures the bumper end caps to the bumper. It grips the edge of the end cap and clips it onto the bumper, holding the...

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Injection Pump Gasket seals the fuel injection pump to its mounting face on the timing case of the 200Tdi and 300Tdi 2.5L turbo diesel engines. Th...

Solenoid Valve Hose for the V8 EFI petrol engine, serving the plenum-mounted solenoid valve. Connects the solenoid valve into the intake plenum on...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...