Land Rover Parts

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Universal Joint is a cross-type (spider) joint fitted within the propshaft assembly, transmitting rotational drive between opposing yokes while acc...

Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...

Stud is an M10 threaded stud, 35 mm long, used as a mounting fastener at several engine locations - the cylinder head, manifold, power steering pum...

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Coolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Inlet & Exhaust Manifold Gasket - 300TDi

This steering drop arm transmits movement from the steering box output shaft to the steering linkage, enabling directional control at the front axl...

Rear Shock Absorber provides damping control on the rear axle for suspension set up with approximately 50 mm of additional travel. Twin-tube const...

Spring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Rear suspension shock absorber designed to control vertical movement of the axle and dampen spring oscillation within the suspension system. This...

Plain Nut - an M10 threaded fastener used at engine and chassis fixing points. Applications include retaining the shock absorber mountings to the ...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Plain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...

Water Temperature Sensor (coolant temperature transducer) that threads into the thermostat housing within the engine cooling circuit. The transduc...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Brake Disc, front, vented. Part of the front braking system. The disc mounts to the front wheel hub and rotates with the wheel; the brake caliper ...

Spring Retention Ring for the front coil-spring suspension. It clamps the upper end of the road spring, securing it against its seat on the chassis...

Front door window regulator forming part of the door glass operating assembly, responsible for controlled raising and lowering of the electric wind...

Fuel Pressure Regulator mounts on the fuel rail of the multiport electronic fuel injection (EFI) system. It holds a constant pressure difference b...

Air Filter Element is the replaceable filtration element of the engine air intake system. It seats inside the air cleaner housing and traps dust an...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Differential Guard for the axle differential, protecting the diff housing and cover from impact damage off-road. Clamps over the differential cent...

Carburettor Grommet for the twin Stromberg carburettor installation on the V8 petrol engine. It sits in the air cleaner and carburettor air intake ...

Wheel Spacer Set, 30 mm: silver alloy wheel spacers for a 5x165 hub, supplied as a set of four with a complete set of wheel nuts. Machined from bi...

Oil Pump Relief Valve Spring for the 3.5L V8 petrol engine lubrication system. The spring sets the opening pressure of the oil pump pressure-relie...

Spark Plug for the petrol engine ignition system, fitted to the 2.5L four-cylinder and 3.5L/3.9L V8 petrol engines. It screws into the cylinder he...

Exhaust mounting spacer tube

Size/Diameter: 1/4" unf x 7/8"

Auxiliary Belt - ancillary drive belt for the 200 TDi engine. Runs from the crankshaft pulley to drive the engine ancillaries such as the alternat...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Copper Sealing Washer used to seal a threaded or banjo joint in the fuel and lubrication circuits. The soft copper deforms under tightening to con...

Brake Caliper is the front left-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against t...

Brake Caliper is the front right-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against ...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 2-3/4" shank length. This is an engine-area fixing for early Series application...

Brake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Front Mud Flap Kit, supplied as a left and right pair. Mounts behind the front wheel arches to reduce spray, mud, and stone throw from the front w...