Land Rover Parts

Hexagon Bolt - an M10 x 45 mm high-tensile bolt, property class 10.9, used in the suspension top link, fulcrum and ball joint assembly. The 10.9 g...

Caliper Seal - internal bridge seal for the front brake caliper. This O-ring sits between the two halves of the caliper body and seals the fluid pa...

Rocker Shaft for the valvetrain of the Rover V8 petrol engine. The shaft mounts on the cylinder head and carries the rocker arms, transferring pus...

Steering box sector shaft seal kit for the steering system. This kit contains the sealing components required for the sector shaft assembly withi...

Cylinder Head Gasket for the Rover V8 petrol engine, sealing the joint between one cylinder head and the engine block. It seals the combustion cha...

Gasket kit 300tdi lower block set no rear crankshaft seal

Tow Ball 50mm flange-fixing tow ball for use with a bolt-on tow bar drop plate. Rated for a maximum gross trailer weight of 3.5 tonnes, with a D-v...

Starter Motor for the 3.5L V8 petrol engine, operating in the engine starting circuit. When energised through the starter solenoid, the pinion is ...

Track Rod End Assembly for the steering linkage, connecting the track rod to the steering drop arm and transmitting movement from the steering box ...

Spark Plug is an ignition-system component for petrol engine applications. Threaded into the cylinder head and connected to the HT lead, it delive...

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Radius Arm Bush mounts at the axle end of the front radius arm, within the front suspension radius arm and axle location assembly. It forms the co...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Spring Seat for the front coil spring suspension. It forms the lower seat that locates and supports the base of the front coil spring on the axle, ...

Reverse Light Switch for the R380 5-speed manual gearbox, completing the reverse lamp circuit when reverse gear is engaged. This switch threads in...

Seal Ring - a copper crush-type sealing washer. It fits beneath a threaded plug or at a metal-to-metal joint and deforms as it is tightened, takin...

double washer, restrictor

Spring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...

Extended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Bolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...

Brake caliper piston rear

Brake & Clutch Pedal Bush for the pedal box assembly. It forms the pivot bearing where the pedals mount on their shaft, locating the brake and ...

Disc brake

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap). A miniature bayonet bulb used in number plate, side, interior and rear lamp positions.

Bracket tie bar for steering box

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Thermostat Housing Gasket seals the thermostat housing (water outlet elbow) to the intake manifold on the 3.5L carburettor V8 engine. It sits in t...

Steering Box Seal Kit reseals the input shaft of the 4-bolt power steering box within the power-assisted steering circuit. The input shaft is wher...

Clutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...

Top Coolant Hose for the engine cooling circuit. Carries hot coolant from the engine outlet at the thermostat housing to the top tank of the radia...

Oil Pump Shaft & Gear for the 3.5L V8 petrol engine, part of the lubrication system. The shaft and its drive gear transmit rotation from the ca...

Oil Pump Gear for the 3.5L V8 engine oil pump, part of the lubrication system. The oil pump draws oil from the sump and pressurises it for deliver...

Indicator, Horn and Headlamp Dip Switch - steering column stalk for LHD applications, mounted on the right-hand side of the steering column. This ...

Master Lighting & Indicator Switch, a column-mounted stalk within the steering column switch assembly. It controls indicator operation and head...

Anti-Squeal Shim for the rear brake pads - left-hand side. This shim fits between the brake pad backing plate and the caliper piston to dampen vib...

Spring Washer, 5/16" - a single-coil split washer fitted under a nut or bolt head to maintain clamp tension. The split coil acts as a spring, exer...

Spring Washer is an M8 double-coil spring washer used as a fastening component in body and chassis assemblies. The double-coil spring form maintai...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Clutch Driven Plate (235mm) transmits engine torque from the flywheel to the gearbox input shaft within the clutch assembly. The friction plate sp...

Headlamp Bezel - stainless steel, 7". The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...