Land Rover Parts

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Drive flange for the front axle drive shaft hub assembly. This component provides the splined connection between the drive shaft and the wheel hub,...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Tap screw

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Oil seal designed to retain lubricant and prevent contamination at the stub axle interface. The seal fits into the stub axle and forms a barrier b...

Front Cover Oil Seal

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Fulcrum Bracket and Ball Joint Assembly for the rear A-frame (top link). The bracket forms the apex of the A-frame and bolts to the rear axle; the ...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Side Repeater Lamp - Front is part of the exterior lighting system, mounting in the front wing to give a side-on indication of the direction indica...

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Exhaust Gasket for the front exhaust section on 2.5L TDi and V8 petrol engines. On 2.5L 200 TDi and 300 TDi 4-Cylinder engines this gasket seals t...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Circlip for the drive shaft and hub assembly on Land Rover permanent four-wheel drive axles. This circlip locates in a machined groove on the driv...

Shock absorber bush (eye), anti roll bar bush

Exhaust Gasket - V8 for the exhaust downpipe assembly on V8 petrol engines. This gasket seals the flange joint at the exhaust downpipe, maintainin...

Steering Damper Stabiliser - a hydraulic damper fitted within the steering linkage assembly to control the oscillation and vibration transmitted th...

Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...

Windscreen Washer Pump, 12V electric, for the windscreen washer system. The pump draws screen-wash fluid from the washer reservoir and delivers it ...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Fir Tree Fastener in light grey, for the roof trim and headlining assembly. Push-fit fastener that secures roof trim panels and headlining ancilla...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Water Pump Housing Gasket for the 300 TDi cooling circuit, sealing the coolant pump distance piece to the cylinder block. The gasket forms the coo...

Transfer Box Gear Lever Knob fitted to the LT230 transfer box gear lever in vehicles where the LT230 is paired with the LT77 main gearbox. The lev...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Track Rod End with a right-hand thread, forming part of the steering linkage. The track rod end is the articulating ball joint that connects the t...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

This taper roller bearing is designed for installation in the lower swivel pin housing, providing controlled rotational support and load distributi...