Land Rover Parts

Tow Ball – 50 mm a black-finished towing ball for flange-type towing brackets. The ball bolts to the face of the towing bracket on the standard tw...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Silicone Intercooler & Turbo Hose Kit - a set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing the standard...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Return to Centre Steering Damper for installation within the steering linkage assembly. This unit mounts between the axle steering arms and the st...

Steering Damper - Heavy Duty Type for the steering linkage assembly on Discovery 1 and Range Rover Classic. This hydraulic damper is mounted betwe...

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Body Mounting Kit renews the body-to-chassis mounting points, where the body is located and secured to the chassis frame. The rubber mounts isolat...

A-Frame Ball Joint Boot is the protective gaiter that seals the ball joint at the apex of the rear suspension A-frame. The A-frame locates the rea...

Polyurethane Boot - Defender - Discovery 1/2 - RRC - P38

Double Cardan Joint Kit for the Discovery 2 front propshaft. The Discovery 2 front propshaft uses a double cardan joint assembly incorporating thr...

Stepper Motor is the idle air control stepper motor mounted on the inlet manifold plenum chamber of the V8 EFI petrol engine. Driven by the engine...

Track Rod Clamp Kit secures the track rod within the steering linkage assembly, holding the joint in position so the steering geometry stays set. ...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Gasket kit carburettor Zenith Stromberg 175CD

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Clutch Slave Cylinder Push Rod for V8 applications, part of the hydraulic clutch release circuit. The push rod transfers movement from the slave c...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Rocker Cover Gasket Set for the 2.5L VM turbo diesel engine, sealing the rocker cover to the cylinder head. The gasket seats between the rocker co...

Warning Bulb Switch (Red) for the facia auxiliary switch panel. Mounted in the upper facia switch bank, this illuminated switch carries an integra...

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Radiator Hose is the bottom (lower) coolant hose in the engine cooling system, connecting the radiator outlet to the water pump inlet. It carries ...

Washer

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Magnetic Drain Plug for the engine oil sump and the LT230 transfer box drain ports. The magnetised tip captures ferrous wear particles suspended i...

Crown Wheel Bolt secures the crown wheel (ring gear) to the differential carrier within the axle differential. Threaded 3/8 UNF and 1.1/8 inch lon...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Polyurethane bushes

Panhard bush RR >'85

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Front suspension shock absorber designed to control spring oscillation and maintain tyre contact with the road surface. Twin-tube low-pressure ni...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

Amber Switch Bulb for the heated windscreen and auxiliary switches. This small bulb provides the amber illumination within the switch, lighting th...

Dislocation Cone - Rear Coil Spring for the rear coil spring seat assembly. When long-travel shock absorbers or lowered top-mount shock relocators...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

thrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...