Land Rover Parts

Cap bolt

Plain Washer M8

Power Steering Pump - Hobourn-type hydraulic pump serving the power-assisted steering circuit on V8 engines. It is driven from the crankshaft by a ...

Front Door Hinge Set Screw secures the front door hinge to the body pillar and door within the door mounting hardware. It clamps the hinge leaf in...

Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...

Enhance the steering strength and responsiveness of your Land Rover Discovery 1 and Range Rover Classic with these heavy-duty steering arms. He...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Upgrade or replace your steering wheel boss with this high-quality 36-tooth adapter, designed specifically for Land Rover Defender to 1991 90/110 v...

Valve Stem Seal - the seal fitted over the valve stem in the cylinder head to control the oil that passes down the stem into the port. This is the...

Accelerator Cable - throttle cable for TDi diesel applications. It connects the accelerator pedal to the injection pump throttle lever, transmitti...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Exhaust Downpipe (Y-Pipe) - the front section of the exhaust system that bolts to the exhaust manifolds. The Y-pipe collects the exhaust flow from...

Dump Valve

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Window regulator front RH

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Front Cover Gasket for the 2.5L 200TDi diesel engine, the smaller of the front cover gaskets. It seals the joint between the front cover and the c...

Polyvee Belt 3.9V8 1253mm

Bolt Threaded fastener used within the exhaust system assembly.

Piston

The cable forms the mechanical link between the handbrake operating lever and the handbrake mechanism within the handbrake assembly, transmitting l...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Green Bulb for the facia and auxiliary switch panel. This small bulb provides the green illumination behind the dashboard auxiliary switches and u...

Bolt and Washer - an M8 x 25 mm hexagonal-head bolt supplied with a washer. A general-purpose threaded fastener used at various fixing points on t...

Tensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...

Tappet Slide for Land Rover 4-cylinder engines, covering the Series I, Series II, Series IIA, and Series III (2.0L Diesel and 2.25L Petrol and Dies...

Power Steering Hose - the high-pressure feed line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pu...

Brake lever kit

Rear Exhaust Silencer Assembly is the rearmost section of the exhaust system, comprising the rear silencer box and tailpipe. It attenuates exhaust...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Fuel Tank Sender is the in-tank fuel level sensing unit within the fuel gauge circuit, for V8 applications. Mounted inside the fuel tank, a float ...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Headlamp Assembly is a complete halogen front headlamp unit within the exterior lighting system, supplied with its integral manual levelling mechan...

Fuel Hose for the 3.5L V8 twin-carburettor engine, part of the carburettor fuel supply plumbing. It connects the fixed points in the fuel feed lin...

Lock Extension - Upper Tailgate - RH is part of the upper tailgate locking assembly. The lock extension links the upper tailgate lock to its latch...

Oil Feed Pipe - Turbo supplies pressurised engine oil to the turbocharger in the 300 Tdi lubrication circuit. It carries oil from the cylinder blo...

Speedometer Angle Drive is a right-angle gear adapter fitted in the speedometer drive line, configured for the right-hand (RH) routing. It takes t...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Fuel Filler Hose

Relay

Alternator is the charging-system generator that supplies current to the battery and vehicle electrical system. Driven from the crankshaft by the ...

Bolt is a general-purpose imperial-thread fixing with a 5/16-inch UNC (Unified Coarse) thread and a 7/8-inch length. Used as a common fastener acr...

Hub Oil Seal for the front axle, sealing the front hub and drive shaft assembly to retain hub lubricant and exclude water, dirt and grit from the w...

Fuel Tank Bolt - a mounting bolt that secures the fuel tank to the chassis. It fixes the tank at its mounting point and is specified for the metal...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...