Land Rover Parts

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Gasket - Front Cover for the VM Motori 2.5L Turbo Diesel engine. This gasket seals the engine front cover to the cylinder block face, providing an...

Front Coil Spring - front suspension coil spring, seated between the axle spring pad and the chassis spring turret to support the vehicle and contr...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Relay operates within the anti-theft alarm and central locking circuit. This relay switches power to the alarm and remote central locking system, ...

Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...

Front Propeller Shaft for the Range Rover Classic driveline. The propeller shaft transmits drive from the transfer box front output to the front ax...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Screw hex HD 3/8" UNC x 1-1/4"

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Steel Wheel - a 5.5J x 16 inch tubeless welded steel road wheel, finished in black. The rim carries a 35 mm offset (ET35). Its welded tubeless con...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Front Coil Spring, part of the front coil-sprung suspension. The spring fits between the chassis spring seat and the front axle, supporting vehicl...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Rear Bumper in a black finish, forming the rearmost impact member bolted to the rear chassis crossmember. Supplied less the styling kit, so it com...

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

Brake Disc - a vented front brake disc for the front axle braking system. The disc rotates with the front wheel hub and is clamped by the caliper ...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Rubber Buffer

Seal Washer - Turbocharger Copper sealing washer for the turbocharger oil feed circuit. It seals the banjo union on the turbocharger's oil supply ...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Rivet is a body fixing used to secure sheet-metal panels, wheelarch liners and trim to the vehicle structure. It forms a permanent, vibration-resi...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Rocker Cover O-Ring for the VM four-cylinder turbo diesel engine, sealing the rocker (cam) cover to the cylinder head. It maintains the oil-tight ...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Clevis pin

Retaining Clip for the front door lock, also known as the door lock plate.

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Exhaust Bracket for the exhaust mounting system. This bracket supports the exhaust line at the section immediately behind the front silencer, loca...

Accelerator Cable for the Range Rover Classic 3.5L V8 carburettor engine, left-hand drive, manual transmission. This cable connects the accelerato...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Thermostat regulates coolant flow within the engine cooling circuit of the 2.5L 4-cylinder VM Turbo Diesel. Housed in the thermostat housing at th...

Rear Side Door Channel is a glass run channel mounted within the rear side door, fitted to the right-hand (RH) side. The channel locates and guide...