Land Rover Parts

O-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. This pulley operates within the A/C belt drive circuit, maintaining ...

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Lock Nut secures the tappet adjuster screw on the rocker shaft, holding the valve clearance once it has been set. Tightened against the rocker arm...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Driving Member Bolt secures the driving member, or drive flange, to the wheel hub. The driving member transmits drive from the axle halfshaft to t...

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Window Regulator for the left-hand front door, operating the manual window lift mechanism. The regulator converts the rotation of the winder handl...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Shaft coupling

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Jet windscreen wash RRclassic 1986 - 1991

Temperature Transmitter is the coolant temperature sender within the engine cooling and instrument gauge circuit, for V8 petrol applications and ca...

Axle Breather Pipe Clip from the axle breather system, retaining the breather hose along its run from the axle case up to its higher mounting point...

Radiator Top Hose carries heated coolant from the engine outlet to the upper radiator inlet within the cooling circuit, delivering it to the radiat...

Pas op alle  V8 benzine motoren met Stromberg carburateurs

Pulley

Oil Dipstick Tube for the 300 TDi engine, guiding the dipstick down into the sump. Houses and locates the engine oil dipstick, providing the passa...

Plenum Chamber Gasket for the V8 EFI petrol engine, part of the air intake and induction assembly. The gasket seals the joint at the plenum chambe...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Power Steering Pump - the engine-driven pump at the heart of the power steering hydraulic circuit. Belt-driven from the engine, it draws fluid fro...

Front Wiper Motor for the windscreen wiper assembly. The motor drives the wiper linkage and wheelboxes that sweep the front wiper blades across the...

Receiver Dryer for the air conditioning system, compatible with R134a refrigerant. Installed on the high-pressure side of the A/C circuit, between...

Engine Mounting Rubber for the 2.5L 200 TDi engine mounting system. This rubber-to-metal mount locates between the engine mounting foot and the cha...

Water Pump for the 2.5L VM Turbo Diesel engine, part of the Engine Coolant Circulation Assembly. The pump circulates coolant continuously through ...

O-Ring for the fluid suction pipe of the ZF four-speed automatic transmission. Seals the joint at the suction (pick-up) pipe that draws automatic ...

Fuse rated at 7.5A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 7.5 amps, the fuse breaks the connection...

Servo unit RRcl D1

Fitment: All models (VIN) LA930456 on

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Intercooler Hose for the 200 TDi turbocharged induction system. Part of the charge-air ducting that links the intercooler into the boost circuit, ...

Gearbox Gaiter Grommet seals the point where the high/low transfer lever passes through its gaiter on the LT95 four-speed gearbox. Fitted to the t...

Bumper End Capping, front left-hand - the end finisher fitted to the outer end of the front bumper. It closes off the open end of the bumper, givi...

Alternator of the Lucas A133 type, rated at 85A, for V8 EFI petrol engines. Driven by the auxiliary belt from the crankshaft as part of the engine...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Drive Screw is a countersunk-head self-tapping screw used to secure body and interior trim components. The self-tapping thread cuts its own mating...

Viscous Fan Assembly for the engine cooling system, mounting to the viscous coupling unit on the front of the engine. This 16", 7-blade white fan ...

Exterior Door Handle Seal for the door locks and handles assembly. The seal sits between the outer door handle and the door skin, closing the gap ...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

CV Joint Spacer for the front axle drive shaft. Fits on the front halfshaft to correctly space the constant-velocity (CV) joint, setting its seati...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...