Land Rover Parts

Clutch Push Rod (9.2 cm) for the clutch release hydraulic circuit, working between the clutch slave cylinder and the release lever. The rod transm...

Boost Pipe Assembly for the 2.5L 300 TDi turbo diesel, part of the turbocharger boost control circuit. It connects the inlet manifold to the injec...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Exhaust Mounting supports the rear section of the exhaust system, suspending it from the underbody. This rubber mounting locates the rear of the t...

clamp exhaust pipe RRclassic (with twin exhaust pipes)

Exhaust Downpipe - V8 - RH - RRC

Window Regulator operates the manual front door glass on the right-hand side, forming part of the door window lift assembly. Mounted inside the do...

Oil Separator Drain Hose for the crankcase ventilation system on the 2.5L naturally aspirated diesel and 200TDi turbo diesel engines. It drains th...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Hex-Head Setscrew, M6 x 20 mm, metric thread, fully threaded to the head. A general-purpose fixing used to secure components at M6 mounting points.

Bolt 3/8" x 2"

Philidas Nut is a 5/16" UNF all-metal self-locking nut. A deformed collar gives it prevailing-torque resistance to loosening under vibration, and i...

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...

Heater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...

Trim Pad Clip is a fastening clip used to secure interior trim pads to the bodyside and door structure. It locates into a pre-formed hole in the p...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

Outer Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Camshaft O-Ring for the 2.5L four-cylinder diesel engines, including the naturally aspirated diesel, turbo diesel and 200TDi. This O-ring forms th...

Timing Belt Tensioner Washer for 200TDi and 300TDi engines. This slotted packing washer fits to the timing belt tensioner assembly, setting the co...

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...

Inlet Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaft,...

Exhaust Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaf...

Joint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...

Hex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...

Bolt - M12 x 60mm is a metric hexagon head bolt used across a wide range of assembly applications on Land Rover vehicles. Thread specification M12...

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...

Vacuum Pump O-Ring that seals the diesel vacuum pump at its mounting joint. The vacuum pump supplies the depression used by the brake servo on die...

Locking Washer for the swivel pin housing on the front axle. The washer sits under the swivel pin retaining bolts, and its tab is bent up against t...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Fuse - 10A for Land Rover electrical systems. This 10A fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Sac Snap Clip

Oil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Valve Stem Seal fits over the valve guide at the top of the cylinder head on the 2.5L 200 TDi and 300 TDi diesel engines. It wipes and meters lubr...

Throttle Potentiometer Gasket seals the throttle position sensor (throttle potentiometer) to the throttle body on the V8 EFI system. It forms the ...

High-Tensile Bolt - 1/2" UNF x 3" for use in Land Rover chassis, body, and mechanical assemblies where a 1/2" UNF thread and 3" length is specified...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Locking Wheel Nut Set for alloy wheels that use the original alloy wheel nuts, securing the road wheels against theft. The set includes 5 locking ...

Accelerator Cable for EFI engines - left-hand drive applications. This cable runs from the accelerator pedal to the throttle body, transmitting pe...

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Wheel Stud - Front Drive Shaft Hub is a press-fit threaded stud for the front drive shaft hub assembly. It provides the fastening point that secure...