Land Rover Parts

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Kit - 7 Inch Headlamp Fixing - Series - Defender

Headlamp Mounting Gasket for the headlamp assembly. A rubber gasket that seats between the headlamp unit and the body aperture surround. It provid...

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...

Fuel Pump is a low-pressure in-tank unit forming part of the fuel delivery system on petrol applications. Mounted inside the fuel tank, it acts as...

Drop Arm - LHD - D1/RRC

Bottom Radiator Hose - the lower coolant hose in the engine cooling circuit, connecting the radiator outlet to the water pump inlet. It returns co...

Handbrake Cable transmits lever movement to the transmission handbrake, the drum brake mounted on the transfer box rear output. The outer sheath i...

Bump Stop limits suspension travel within the suspension assembly, cushioning the contact between the axle and chassis at the extremes of wheel mov...

Radius Arm Bush Set - Polyurethane fits at the axle end of the front radius arms, within the front suspension radius arm and axle location assembly...

Coolant hose RRcl 3.5

Windscreen Seal is a rubber glazing seal fitted around the windscreen aperture. It retains the windscreen glass in the body aperture and seals the...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Differential Lock Link Assembly for the LT230 transfer box, fitted to vehicles with the LT77 or LT85 5-speed manual gearbox (28D prefix). This lin...

Idler Pulley - timing belt idler for the 200 TDi and 300 TDi engine. Provides a bearing surface on the timing belt path, guiding the toothed belt ...

Fuel Temperature Sensor for the EFI V8 petrol engine, part of the electronic fuel injection management system. The sensor measures the temperature...

Crankshaft Pulley Bolt for the 2.5L 300TDi diesel engine. This bolt secures the crankshaft pulley and torsional vibration damper to the nose of the...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. Positioned within the A/C belt routing circuit, this pulley guides t...

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...

Instrument Voltage Stabiliser for the Range Rover Classic instrument cluster assembly. This component regulates the voltage supply to the instrume...

Swivel Housing Kit providing a complete overhaul of the front axle swivel assembly for one side, supplied complete with the swivel housing ball. T...

Camshaft Bearing, the front bearing in which the camshaft front journal runs within the cylinder block. It supports the forward end of the camshaf...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Body Mount Spacer Tube forms part of the body-to-chassis mounting assembly, located at a mount point between the body and the chassis frame. It se...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Ballast Resistor Resistor in the ignition primary circuit of the 3.5L V8 petrol engine. Wired in series with the ignition coil, it drops the suppl...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Mudshield

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

special bolt for rocker shaft 200 TDI three per engine. sold EACH! - 90/110/130 - Discovery - Range Rover Classic

Intercooler Hose for the 200TDi 2.5L turbocharged diesel engine intercooler circuit on the Discovery 1 and Range Rover Classic. This hose forms pa...

Drive Belt is the serpentine (poly-vee) accessory belt for the 4.0L V8 EFI petrol engine fitted with air conditioning. Driven from the crankshaft ...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Steering lock

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Brake Light Switch operates the stop lamps within the braking system's electrical circuit. Mounted at the brake pedal, the switch closes when the ...

Oil Filler Cap Seal fitted between the oil filler cap and the rocker cover opening, sealing the point where the cap closes onto the cam cover. It ...

Protector for the fuel pipe system, fitted within the fuel pipes assembly on petrol applications. Used on Defender with 2.8L 6-cylinder BMW M52 pet...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Rear Side Glass - Right-Hand for the Range Rover Classic 4 Door Station Wagon body. Fixed rear quarter window glass for the right-hand side of the...

Clutch Driven Plate for the LT95 four-speed gearbox, V8 petrol. The driven plate (friction disc) is splined to the gearbox input shaft and clamped...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Drive Flange Bolt secures the drive flange to the wheel hub on the axle. Supplied as a set of 10. These bolts are used with the DA1148 and DA1149 ...

Timing Belt for the camshaft drive of the 300 TDi diesel engine, running within the timing belt and tensioner assembly at the front of the engine. ...