Land Rover Parts

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Fuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Exhaust Mounting Rubber - flexible support that suspends the silencer section of the exhaust system from the vehicle underbody. The moulded rubber...

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Fuel Filter with a paper filter element, for carburettor petrol engines. Part of the fuel supply system. The filter is plumbed inline between the ...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Gearbox Filter for the LT77 five-speed manual gearbox. This gauze oil strainer sits in the gearbox lubrication circuit, screening the oil drawn thr...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Electric Fuel Pump mounted externally in the fuel supply system, drawing petrol from the tank and delivering it to the carburettor. This is an ext...

Needle Roller Bearing for the front axle swivel pin housing. The bearing seats in the swivel housing bore and carries the stub axle, providing rad...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Front Axle CV Joint, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft and transmits ...

Gear Lever Knob for the LT77 5-speed manual gearbox. Fits the main gear lever of LT77-equipped vehicles, including V8 petrol manual variants. The ...

Mudflap fitted at the trailing edge of the wheel arch to control road spray, mud and debris thrown from the tyre. Mounted at either the front or r...

Stub axle

Flange Bolt securing the rear output (propshaft) drive flange to the output shaft of the LT230 transfer box. Manufactured to a high-tensile specif...

Drive Belt - 10mm × 1025mm for the auxiliary drive system on the 2.5L 4-Cylinder diesel and 200TDi engines. This poly-V ribbed belt drives the alt...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Nyloc Nut - M14 - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under vibra...

Joint Washer - 4-Wheel ABS installed at the stub axle interface in the hub assembly of vehicles equipped with 4-wheel ABS. This asbestos-free gask...

Split Pin

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Automatic Drive Belt Tensioner for the front-end accessory drive system, maintaining correct tension across the auxiliary belt that drives the alte...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Coolant Hose for the water pump circuit on the 3.5L V8 Twin Carb petrol engine. This hose connects the water pump outlet to the coolant pipe, rout...

Differential flange 4-spline

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Washer Pump for the windscreen washer system, running on a 24-volt electrical supply. The pump draws fluid from the washer reservoir and delivers ...

Serrated Washer with a 3/8" bore, a serrated locking (shakeproof) washer. Fitted beneath a bolt head or nut, the serrated teeth bite into both the...

Speedometer Cable – LHD is the mechanical drive cable that transmits road speed to the speedometer. The rotating inner core runs inside a protectiv...

Steering Box Seal Kit - Sector Shaft

Front door window regulator assembly for left-hand front door applications within the door glass operating mechanism. This component forms part o...

Inside Door Handle Bezel The interior trim escutcheon that surrounds the door release handle on the inner door panel, finishing the opening around ...

Fuel Filter Element for the carburettor fuel supply circuit on Land Rover V8 petrol engines. Fitted in-line on the fuel feed pipe between the fuel...

Drain Plug Removal Tool for slackening and refitting the square-recess oil drain plugs fitted to Land Rover axles, gearboxes and engine sumps. The...

Fan belt OEM DAYCO 10mm wide, 1235mm long

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Speedo drive oil seal LT230