Land Rover Parts

Front Propeller Shaft connecting the transfer box front output to the front axle differential. It transmits drive from the transfer box to the fro...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Reverse Idler Gear for the LT77 five-speed manual gearbox. The reverse idler sits between the layshaft reverse gear and the mainshaft reverse gear...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

Front Drive Flange Spacer for the LT230 transfer box. Fits on the transfer box front output shaft behind the drive flange, setting the correct sha...

Bolt Flanged hex-head bolt. Used to secure the timing belt and tensioner on diesel engines, and as a starter motor and drive plate fixing.

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Drive Belt Air conditioning compressor drive belt for the 200TDi turbo diesel engine, poly-vee (multi-rib) construction. Drives the A/C compressor...

V Belt Accessory drive belt for the 2.4L four-cylinder VM turbo diesel engine. Transmits drive from the crankshaft pulley to the alternator and wa...

Glow Plug for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It forms part of the cold-start pre-heating system. The glow ...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Fuel Injector for the fuel injection system of the 2.5L 200 TDi diesel engine. The injector atomises high-pressure diesel delivered from the injec...

Engine Lifting Bracket for the front of the 2.5L 200 TDi and 300 TDi diesel engines. The bracket bolts to the engine and provides a rated lifting ...

Trap Assembly - Fuel

Carburettor (right-hand) for the 3.5L V8 twin-carburettor petrol engine. The carburettor meters fuel into the incoming air stream to form the comb...

Carburettor (left-hand) for the 3.5L V8 twin-carburettor petrol engine. The carburettor meters fuel into the incoming air stream to form the combu...

Fuel Injector

Fuel Pump is the in-tank electric fuel pump in the fuel delivery system, mounted within the fuel tank. It draws fuel from the tank and delivers it...

Fuel Tank Pump Sealing Ring for the fuel tank pickup and pump assembly. Seals the pump/pickup unit where it mounts to the top of the fuel tank, pr...

Catalytic Converter for the V8 petrol exhaust system. It treats exhaust gases to reduce emissions, fitted in the exhaust line on applications equi...

Rear Exhaust Silencer for the 200/300 TDi diesel exhaust system. It forms the rearmost section of the exhaust, attenuating gas-flow noise before t...

Air Filter Element is the replaceable filtration element of the engine air intake system. It seats inside the air cleaner housing and traps dust an...

Cylinder Head Gasket for the 300 TDi 2.5L four-cylinder turbo diesel engine. It seals the joint between the cylinder head and the engine block, co...

Timing Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Flywheel Assembly for the manual transmission on the 2.5L 200 TDi and 300 TDi turbo diesel engines. Bolted to the rear of the crankshaft, the flyw...

Flywheel Assembly for the manual transmission on the 2.5L 200 TDi and 300 TDi turbo diesel engines. Bolted to the rear of the crankshaft, the flyw...

Injection Pump Support Bracket for the fuel injection system on the 2.5L 300 TDi turbo diesel engine. The bracket ties the injection pump to the e...

Seal - Oil Pump

Distributor for the 3.9L V8 EFI petrol engine ignition system. Driven from the camshaft, it routes high-tension voltage from the ignition coil to ...

Fuel Injection Pump Plate for the 2.5L 300 TDi turbocharged diesel engine, a component of the ERR5057 mechanical injection pump within the diesel f...

Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...

Cylinder Head Assembly for the 2.5L 300 TDi turbocharged diesel engine - the upper closure of the combustion chambers, carrying the valve seats, gu...

Cylinder Head for the 2.5L 300TDi diesel engine, the upper casting that closes the top of the cylinder block. The cylinder head carries the valves...

Tappet Adjusting Screw for the 2.5L 300 TDi turbocharged diesel engine, fitted in the rocker arm of the valvetrain. Threaded into the rocker arm t...

Rocker Cover Screw for the 2.5L 300TDi diesel engine, securing the rocker (valve) cover to the top of the cylinder head. This hex screw with a fem...

Timing Belt Cover for the 2.5L 300TDi diesel engine, forming part of the front timing belt enclosure. The cover sits over the toothed timing belt ...

Belt - Polyvee - Petrol

Front Crankshaft Oil Seal for the 2.5L 300TDi turbo diesel engine. It fits around the crankshaft nose at the front of the engine, sealing the point...