Land Rover Parts

Mainshaft 3rd Gear Bush - LT77 is the bearing bush for 3rd gear on the mainshaft of the LT77 5-speed manual gearbox. It sits between the mainshaft...

Clutch Release Pivot for the clutch release mechanism, mounted inside the bellhousing. The pivot provides the fulcrum on which the clutch release ...

Grommet - moulded rubber grommet for a panel or component aperture. Fitted into a drilled or pressed hole to line the opening, it provides a seal ...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Wiring Connector for the chassis wiring harness, used in the fuel tank circuitry. The connector forms a serviceable electrical junction between ha...

Brake Pad Wear Indicator Harness - the wear-warning wiring harness within the braking system. This harness connects the brake pad wear sensors to ...

Exhaust Bracket for the exhaust system mounting. The bracket supports and locates a section of the exhaust line against the underbody, typically w...

Heater Hose - Outlet is a moulded coolant hose in the cabin heater circuit, routing engine coolant between the cooling system and the heater matrix...

Hose RVS

Exhaust Clamp a clamp for the exhaust system on 4-cylinder TDi applications. It secures the joint between two exhaust sections, holding the pipes ...

Pipe Adaptor is a double-male union fitting in the automatic transmission oil cooler circuit. It joins two pipe runs, carrying transmission fluid ...

Breather Hose is part of the crankcase ventilation system on the 3.5L V8 twin-carburettor petrol engine. It routes breather gases through the vent...

Door Glass Channel the glass run channel within the door assembly. The channel guides the door glass as it is raised and lowered by the window reg...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Oil Cooler Hose A hose in the oil cooling circuit of the 2.4L VM 4-cylinder diesel engine, routing oil between the engine and the oil cooler. It c...

Bumper Mounting Bracket - front bumper mounting, right-hand side. This bracket forms part of the front bumper mounting and secures the bumper to t...

Dash Assembly Bracket - a structural support bracket forming part of the dashboard (fascia) assembly. The bracket provides a fixing point within t...

Coolant Adaptor (Reducer) - threaded adaptor in the engine oil cooler circuit at the radiator. This threaded reducer adaptor connects the engine o...

Input Shaft is the primary (input) shaft of the manual gearbox, carrying drive from the clutch into the gear train. It takes the clutch output on ...

Pulley 2 Grooves

Fuel Spill Pipe forms part of the fuel injection system on the 2.5L 200TDi turbo diesel engine. It links the injector leak-off unions, collecting ...

Interior Light Delay Relay - the timer relay in the interior lighting circuit. This delay unit holds the courtesy and interior lamps on for a set ...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Coolant Level Sensor for the expansion tank in the engine cooling system. Fitted to the coolant expansion tank, the sensor uses an internal float ...

Lockset - Valeo MUC2085

Reverse Idler Shaft for the R380 5-speed manual gearbox. The shaft carries the reverse idler gear within the gearbox casing. The reverse idler gea...

Sound Deadening Pad is an acoustic pad fitted to the rocker cover on the 2.5L 300TDi turbo diesel engine. It damps mechanical noise radiating from...

Exhaust Downpipe is the cast front section of the exhaust system for the 200TDi and 300TDi diesel engines. It bolts to the turbocharger outlet and...

Interior Door Pull Handle for the front right-hand door of the Range Rover Classic 2-Door Station Wagon. This is the inner grab handle mounted on ...