Land Rover Parts

Synchro Assembly for fifth gear in the LT77 five-speed manual gearbox. The synchroniser matches the rotational speed of the gear to the shaft befo...

Stud is a threaded fastener stud. It provides a fixed threaded mounting point onto which a component is secured with a nut.

Camber Bush Set for the front radius arms, 38mm wide. The bushes locate in the front radius arm mountings and set the caster and camber geometry o...

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.

Edge Clip A black edge clip with a delta-section profile that grips a panel flange. It provides a push-on fixing along the edge of the door assemb...

Carburettor Needle for the SU variable-venturi carburettor in the fuel system of the 3.5L V8 petrol engine, in twin-carburettor configuration. The...

Rear Wheel Arch Extension - Front Section, Left-Hand for the two-door body, an exterior body trim panel. This extension fits to the forward part o...

Oil Cooler Pipe Seal for the transmission oil cooler circuit. The seal fits at the oil cooler pipe union, sealing the connection against fluid lea...

Circlip - LT77 Mainshaft is a retaining circlip used on the mainshaft of the LT77 5-speed manual gearbox. It seats in a groove on the mainshaft to...

Front Housing Gasket - LT77 5-Speed Gearbox This gasket seals the joint between the front housing and the main gearbox casing on the LT77 5-speed ...

Bolt - a washer-faced retaining bolt used in the engine crankcase breather assembly on the 2.5L TDi / 300 TDi diesel engine. It secures the breathe...

Connecting Rod Assembly for the 300TDi 2.5L turbo diesel engine. The connecting rod links a piston to the crankshaft, transmitting the force of co...

Washer – a flat washer used on the 2.5-litre 300TDi turbo diesel engine. The flat washer distributes the clamping load beneath a bolt or nut head.

Capture the sleek design of the Range Rover Evoque with this premium 1:76 scale diecast model in elegant Baltic Blue. This detailed replica perfect...

Wading Kit for the drivetrain and engine breather system, extending the breather points of the axles, gearbox and engine to a higher level. Raisin...

Engine Mount - Right Hand supports the engine at the right-hand mounting point and isolates engine vibration from the chassis. It locates between ...

Rear Brake Caliper for the left-hand side, fitted to installations using solid (non-vented) rear brake discs. The caliper carries the hydraulic pis...

Hub and Stud Assembly - the rear wheel hub for the Salisbury rear axle, supplied complete with wheel studs fitted. The hub carries the rear wheel ...

Oil Filter Adaptor

Differential Gear Kit for the front axle differential. The kit renews the front differential gear set, restoring the designed gear mesh and the to...

Cylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...

Cross Rod End

Mainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...

Front Camshaft Bearing for the valvetrain of the 2.5L four-cylinder diesel and petrol engines. It supports the front journal of the camshaft withi...

Tow Ball & Pin Hitch Assembly for the towing system, mounting to the rear towing bracket. The assembly combines a tow ball for standard ball-c...

Front Brake Caliper is the left-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fro...

Outer Repair Sill - 4-door body, left-hand (nearside). A body repair panel for the outer sill section beneath the door openings. The outer sill is...

Pair of Heavy Duty Rear Half Shafts for 90/Discovery 1/RRC 1994 On & 110/130 2002 On

Static Lap Belt - a two-point lap seat belt for a centre or side-facing seating position. The webbing is a fixed length and is adjusted by hand to...

Mainshaft Gear for the LT230 transfer gearbox, carrying 26 teeth. The gear is mounted on the transfer box mainshaft and forms part of the gear tra...

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Exhaust Bracket A mounting plate in the exhaust system, used at the rear of the twin-pipe arrangement. It secures the rear section of the twin-pip...

Rear Floor Crossmember, a transverse structural member beneath the rear load floor. This crossmember runs across the underside of the body and sup...