Land Rover Parts

Clutch Release Fork Kit for the manual transmission clutch release mechanism, built around a cast release fork. The fork pivots on its mounting in...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

Drive Belt is the auxiliary drive belt for the 3.5L V8 petrol engine. Running from the crankshaft pulley, it drives the alternator and, where fitt...

Brake Pad Fitting Kit - Solid Disc - Front

Courtesy Lamp Switch is the door-pillar plunger switch in the interior lighting circuit. Mounted in the door aperture, it is released when a door ...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Fuel Pump is the in-tank high-pressure pump in the fuel delivery system, mounted inside a metal fuel tank. It draws petrol from the tank and deliv...

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Spring Retainer - rear inner-top retainer in the coil spring and shock absorber mounting. It locates and holds the top of the rear coil spring at ...

LT230 Transfer Box Bottom Cover Gasket, sealing the main casing bottom cover of the LT230 two-speed transfer box. Fits the main casing bottom cove...

Oil Seal for the R380 manual gearbox extension case (rear housing). It seals the output shaft where it exits the extension housing, retaining gear...

Headlamp Washer Jet - Single Nozzle

Hex Nut with a 7/8" UNF (Unified National Fine) thread, used on the power steering box assembly. This large six-sided fastener threads onto a matc...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Oil Cooler Pipe - the pipe carrying engine oil between the oil cooler and the engine within the lubrication cooling circuit of the 2.5L 4-cylinder ...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

EGR Blanking Kit replaces the exhaust gas recirculation (EGR) valve on the 300 Tdi engine, sealing the EGR port on the intake manifold so exhaust g...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Oil Cooler Pipe - the pipe carrying engine oil from the engine to the oil cooler within the lubrication cooling circuit of the 2.5L 4-cylinder TDi ...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Propshaft Bolt Kit - 4 Bolts & 8 Nuts

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Radius Arm Bush - Front - mounts the front radius arm at its axle end within the front suspension. The radius arm locates the front axle longitudi...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Rear Shock Absorber, standard-travel, for the rear axle suspension. The damper controls vertical movement of the rear axle and damps spring oscill...

Mirror Adapter for the exterior door mirror assembly. This adaptor forms the interface between the mirror glass and the mirror body, locating the ...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

7" round LED headlamp 12/24V chrome 78W LHD (pair)

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Clutch Release Bearing Staple is the spring retention clip that secures the clutch release bearing onto the release fork. It holds the bearing in p...

Stop Light Switch mounts at the brake pedal and switches the rear brake (stop) lamps on when the pedal is depressed, operating within the brake-lig...

Facia Louvre Vent Housing for air-conditioned models, mounted in the facia as part of the cabin air distribution system. It carries the directiona...

Speedometer Drive Gear for the LT230 transfer box, located on the rear output and driving the speedometer take-off. This is the 20-tooth gear, ide...

Spark Plug Ignition component for the Rover V8 petrol engine. Threaded into the cylinder head, it carries the high-voltage current from the igniti...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Coolant Bypass Hose for the engine cooling system of the 200 TDi diesel engine. It carries coolant along the bypass path so that flow continues to...