Land Rover Parts

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Special Nut - secures the rear knuckle to the lower and upper suspension arms. It retains the rear suspension arm bolts at the knuckle, holding th...

Bolt Mounting bolt for the front suspension arm. Part of the front suspension assembly, it secures a front upper or lower control arm (wishbone) a...

Right-hand inlet manifold forming part of the air intake system, distributing charge air from the throttle and intake ducting evenly to the cylinde...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Fitment All Models From (V)6A916890

Lower Suspension Arm - Rear - LH for the independent rear suspension assembly. This left-hand lower wishbone forms part of the multi-link rear sus...

CV boot gaiter kit D3, D4, RRsp

Fuel Tank Strap for Discovery 3, Discovery 4, and Range Rover Sport equipped with the 10MY-specification fuel tank (two vent pipes). This strap se...

Relay - 20A 5-pin black micro-format relay for use in vehicle fuse and relay centres. The 5-pin configuration provides both normally-open and norm...

Tailgate Release Switch - micro-switch assembly fitted within the tailgate release mechanism. When operated, the switch provides the electrical sig...

Diff oil seal

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Stud

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Spindle rod link

Compressor assy 9A (compressor only)

Steering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...

Modular Steel Wheel is a heavy-duty 8-hole steel road wheel finished in satin black. Specification: 18 x 8 inch, ET45 offset, 5 x 120 PCD, rated t...

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Air Suspension Connector joins the valve block to a high-pressure air line within the air suspension pneumatic circuit. The fitting forms a sealed...

Vacuum Pump Seal - 2.7 TDV6 is the sealing component for the engine-driven vacuum pump on the 2.7L TDV6 diesel. The vacuum pump is mounted on the ...

ACE filter D2

Parking Aid Sensor, Rear - ultrasonic transducer for the Parking Distance Control (PDC) system, mounted through the rear bumper cover. This is the ...

Front Fog Lamp - Left-Hand for the front bumper lighting assembly. This lamp mounts in the front bumper fog lamp aperture and provides supplementa...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Rear Lower Suspension Arm (Right-Hand) is a lower control arm in the rear independent suspension. It locates the rear hub carrier to the chassis s...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Filter valve assy

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Air Filter - the air cleaner element for the engine air intake system. The element sits within the air cleaner housing and filters incoming air be...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Fitment: All Models 2.7 TDV6 To (V) 6A999999 2.7L TDV6 diesel models to (VIN) 6A999999

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Oil Filter for the 2.7L TDV6 diesel engine, part of the engine lubrication circuit. A paper-element filter that removes wear particles and contami...

Bolt for the rear suspension. It secures the lower mounting of the rear shock absorber to the lower suspension arm, carrying the damper load as the...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Wiper Arm Pivot Nut Secures the wiper arm to the splined pivot spindle of the windscreen wiper mechanism. It threads onto the spindle where it emer...

Rear Wheel Arch Protector Strip trim fitted to the inner edge of the rear wheel arch aperture on the Range Rover Sport L320. This rubber protector...

Parking Brake Actuator Repair Kit - the internal service parts for the electric parking brake (EPB) actuator module. Replaces the worn drive gears...

Brake Drum Clip is a retaining clip within the rear drum-in-hat parking brake (handbrake) assembly. It secures the handbrake shoe against the back...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Air flow meter OEM VDO

Rear Lower Suspension Arm for the rear independent suspension, left-hand side. The lower control arm (wishbone) connects the rear hub carrier to t...

The OEM Service Kit is designed for Discovery 3 (4.4 V8 EFI Petrol) and Range Rover Sport (4.2/4.4 V8 Petrol) models. This kit includes all the ess...