for Discounts / VAT
for Discounts & Correct VAT
Browse our complete range of Land Rover and Range Rover parts- from OEM-quality replacements to specialist upgrades. Whether you’re restoring a classic Defender, maintaining a Discovery, or tuning a modern Range Rover, our parts selection covers every system: engine, suspension, braking, transmission, and more.
Door Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...
View full detailsBarrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...
View full detailsClip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...
View full detailsPTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...
View full detailsEngine & Gearbox Mount - Lower The lower (bottom) rubber mounting that isolates the engine and gearbox from the chassis, absorbing running vibr...
View full detailsRotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...
View full detailsFiller and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...
View full detailsTailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...
View full detailsMetal Fuel Filler Cap seals the fuel tank filler neck, closing the fuel system against contamination, spillage and evaporative loss. The cap secur...
View full detailsFront Chassis Leg for the left-hand (nearside) front of the chassis. A welded chassis repair section that renews the front chassis leg where the o...
View full detailsOutput Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...
View full detailsExhaust Pipe - Intermediate - Non-Station Wagon
Gearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...
View full detailsShock Absorbers for the rear axle, supplied as a matched pair. Each damper controls suspension movement by converting the energy of spring oscillat...
View full detailsSeat Back and Headrest for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant...
View full detailsStrap Stud is a body fixing used in the canvas hood (soft top) and hood frame assembly. It provides an anchor point over which a retaining strap i...
View full detailsReverse Selector Fork for the gear selection mechanism in the Series-type manual gearbox (LT76), suffix B onwards. Mounted on the selector shaft, ...
View full detailsDipstick Tube - the guide tube through which the engine oil level dipstick passes down into the sump. It locates in the cylinder block and directs...
View full detailsRoof Access Ladder in a hot-dip galvanised steel finish, providing safe access to a roof rack. This is a non-drill (bolt-on) type ladder that moun...
View full detailsLayshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...
View full detailsPop Rivet (blind rivet) used to secure the flexible door rubber, a body and door-trim fixing. The rivet fastens the flexible rubber seal to the do...
View full detailsAutolite Work Lamp - Square - 55W
Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...
View full detailsSynchro Hub for the 3rd/4th gear synchroniser assembly in the Series-type manual gearbox (LT76). The hub carries the synchroniser mechanism that m...
View full detailsRear Door Trim Panel - a black interior trim panel that finishes the inner face of the rear side-hinged door, covering the door frame to give a cle...
View full detailsSteering Relay Arm - Upper is the upper lever of the steering relay unit, the vertical relay mounted on the front chassis crossmember that transfer...
View full detailsDifferential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...
View full detailsWater Pump - 2.0 IOE - the engine coolant pump in the cooling system, for the 2.0L IOE (inlet-over-exhaust) petrol engine. Driven by the fan belt ...
View full detailsRear Shackle Pin for the rear leaf spring shackle. The pin secures the spring shackle at the rear mounting of the rear leaf spring, allowing the s...
View full detailsThrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...
View full detailsBall Joint - Accelerator Linkage is a mechanical pivot joint used in the accelerator linkage assembly. This ball joint connects articulating rods ...
View full details4WD Selector Rod for the Series transfer box. It forms part of the four-wheel-drive engagement linkage, transmitting selector movement through the...
View full detailsGearbox Stud is a 1 3/4" threaded stud used in the gearbox and transfer box assembly. It provides a fixed threaded anchor for clamping casing join...
View full detailsTab Washer - Primary Pinion is a locking washer in the manual gearbox primary pinion assembly. Fitted beneath the primary pinion retaining nut, it...
View full detailsRear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...
View full detailsUniversal Joint for the propeller shaft, measuring 82 mm across the bearing caps with a 27 mm cap diameter. The universal joint is the cross-and-b...
View full detailsHook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...
View full detailsBrake Kit - Series - SWB - To June 1980
Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...
View full detailsWheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...
View full detailsMonograde Engine Oil SAE 30 - a single-grade mineral engine oil for early petrol engines built before around 1960. The non-detergent formulation l...
View full detailsExhaust Silencer for right-hand-drive applications, constructed in stainless steel. Part of the exhaust system, this silencer attenuates combustio...
View full detailsWater Pump Impeller in the engine cooling circuit. Pressed onto the water pump spindle and driven by the fan belt, the impeller circulates coolant...
View full detailsMounting Rubber - Upper is the upper rubber of a powertrain mounting. It isolates the engine or gearbox from the chassis frame, damping vibration ...
View full detailsVoltage Regulator (control box) of the screw-terminal type, for dynamo charging systems. The control box is wired between the dynamo and the batte...
View full detailsSpring Clip for the rear end door trim casing, part of the interior trim fixings. The sprung clip retains the rear door card (trim casing) to the ...
View full detailsChoke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...
View full detailsLight Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...
View full detailsThis page lists every Land Rover and Range Rover part stocked across our Dutch warehouse network. With the full catalogue in one place, the fastest way to reach the right component is to narrow down by your model or by the system you are working on, using the links below.
Shop by modelParts for Series-derived, Td5, Puma and L663 Defender generations.
Land Rover Defender partsParts spanning Discovery 1 through Discovery 5 and Discovery Sport.
Land Rover Discovery partsParts for every Range Rover line from Classic to the latest generations.
Range Rover partsParts for Freelander 1 and Freelander 2 across petrol and diesel variants.
Land Rover Freelander partsPanels, mounts, fasteners and structural components.
Land Rover chassis and body parts