Land Rover Parts

Cam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...

Front Wing Panel is the outer body panel that forms the side of the front end over the front wheel arch, part of the front body assembly. Supplied...

Folding Side Step - Series

Reverse Gear for the LT76 four-speed gearbox, Suffix A only. The reverse idler gear is brought into mesh when reverse is selected, reversing the di...

Reverse Shaft for the Series III 4-speed gearbox, Suffix A build. This shaft carries the reverse idler gear within the gearbox casing. It fits the...

Threaded Core Plug seals a threaded aperture in the engine block casting, used on the 4-cylinder petrol engine as a blanking plug for a redundant h...

Anti-Roll Bar Link & Shock Bush Kit renews the compliant mounting bushes in the anti-roll bar link and shock absorber mounting points within th...

Bolt - Spare Wheel Bonnet Mounting for Land Rover Series I, II, IIA, and III models fitted with a bonnet-mounted spare wheel carrier. This clamp b...

Polyurethane chassis- and spring bushes as well as shock absorber bushes for all Series Short Wheelbase and Series 1 and 2/2A LWB. (For S3 LWB use ...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Main Wiring Loom for right-hand drive vehicles, forming the primary electrical harness that distributes power and signal throughout the vehicle. I...

Main Wiring Loom for the petrol vehicle electrical system, forming the central harness of the vehicle. This loom carries the principal electrical ...

Set Screw retaining the top cover plate of the Series gearbox. A 4BA round-head fastener, sherardised finish, used to secure the cover plate on to...

Harness Bracket Shim for the wiring harness mounting hardware. Fitted behind the harness support bracket at its mounting point, the shim sets the ...

7 inch high low beam headlight LHD black, with U shape parking light, (PAIR)

Rear Quarter Panel for the left-hand side, part of the rear body structure. This is the outer body panel that forms the rear side of the vehicle b...

12N 7-Pin Trailer Socket for the towing electrical system, mounted at the rear of the vehicle. The 12N socket carries the standard trailer road-li...

Rear Door Seal for the rear door aperture on Series III and Defender 90 and 110. The rubber seal runs around the perimeter of the rear door apertu...

Inner Ring

Exhaust Bracket Saddle Clamp for the intermediate exhaust pipe on 109-inch wheelbase Series 2 and Series 3 Land Rovers. The saddle clamp locates an...

Layshaft for the Series Land Rover gearbox. The layshaft (countershaft) runs parallel to the mainshaft inside the gearbox casing. It is driven con...

Front Propeller Shaft for the 109" 1-ton Series Land Rover, transmitting drive from the transfer box to the front axle. This propeller shaft runs ...

Choke Cable is the manual choke control cable in the carburettor fuel system, running from the dashboard choke knob to the carburettor choke lever....

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Safari Rear Door Skin - Lower Half. The outer sheet-metal panel for the bottom half of the rear side door (the Safari door), supplied as a repair s...

motor wiper single replacement (NLA wanneer op!)

Voltage Regulator for the dynamo charging circuit – the Lucas RB340 control box. Wired between the C40 dynamo and the battery, the control box reg...

Rear Inward-Facing Seat in black trim. This individual inward-facing seat mounts in the load area to provide additional occasional seating. Inward...

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Mirror Head is a large replacement exterior door-mirror head measuring 265mm x 160mm, offering an increased field of view over the standard head. ...

Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...

Spring - Timing Ratchet sits within the engine timing assembly on Land Rover 2.25L and 2.0L diesel engines. This spring provides the retention for...

Timing Chain Tensioner Spring for Land Rover 2.0L Diesel and 2.25L Petrol and Diesel four-cylinder engines. This spring applies constant pressure ...

Leaf Spring is the rear passenger-side leaf spring for long-wheelbase (LWB) chassis, of 8+2 leaf construction. Land Rover lists it as the left-hand...

Plate grommet GENUINE LR

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Bolt, a threaded fastener used on the 2.0L petrol engine.

Layshaft Bearing Distance Piece Spacer for the layshaft (cluster gear) bearing within the main gearbox. It locates against the layshaft bearing to...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Bush

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...