Land Rover Parts

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Front leaf spring LWB diesel DS

Leaf Spring - Front - 11-Leaf A semi-elliptic front leaf spring built up from an eleven-leaf pack, part of the front suspension. It carries the ch...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Bolt with Whitworth (BSW) thread - 1/4 inch diameter, 1-1/4 inch length, sold individually. Used across Series Land Rover applications requiring t...

Piston for the 2.25L four-cylinder petrol engine, machined to +0.030" oversize for a rebored cylinder block. The piston runs in the cylinder bore ...

Rear Light Guard - Single - Natural is a steel mesh protective guard for a single rear lamp. It bolts over the rear lamp lens to shield it from im...

Rear Bumperettes - a pair of tubular bumperettes that bolt to the rear crossmember to protect the rear corners of the body and the rear lamps from ...

Rear Leaf Spring for Series IIA and Series III 109" wheelbase 1-ton and Extra Heavy Duty Land Rovers. Suitable for both left-hand and right-hand si...

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Camshaft Bearing Set for the Rover 3.5L V8 petrol engine. Supplies the bearing shells that support the camshaft as it runs within the cylinder blo...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Reverse Shaft for the reverse gear train in the Series-type manual gearbox (LT76), suffix B onwards. The shaft carries the reverse idler gear, whi...

Throttle Linkage for the 3.5L V8 fitted with twin Stromberg 175CD carburettors. This linkage connects the throttle pedal input to both Stromberg c...

Upgrade your Land Rover Series 2A & Series 3 SWB (1980-1984, Metric) with this +40mm stainless steel brake hose kit. +40mm Extended Length -...

Load Bay Liner Kit lines the rear load area to protect the original bed and inner surfaces from cargo abrasion, impact and moisture. The liner is f...

Screw for securing the chaffguard to the body structure on Series Land Rovers. The chaffguard protects adjacent components from abrasion and heat;...

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...

Manifold Stud is used to secure the combined inlet/exhaust manifold assembly to the cylinder block on Series vehicles fitted with the 2.25L diesel ...

Overdrive Needle Bearing for the front of the mainshaft in a Fairey overdrive unit. The bearing supports the overdrive clutch sleeve on the mainsh...

Bearing is the front output shaft bearing for the gearbox, a taper roller bearing. It supports the front output shaft within the gearbox/transfer ...

Crankshaft with Bearings for the 2.25L 4-cylinder petrol engine. The crankshaft converts the reciprocating motion of the pistons into rotational o...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Carburettor Bell Crank Bush for the accelerator throttle linkage on the 2.25L 4-cylinder petrol engine. The bush locates the throttle bell crank a...

Sealing Ring - Rocker Cover Breather Bolt for the 2.25-litre 4-cylinder engine. This sealing ring is fitted under the rocker cover breather bolt, ...

Intermediate Shaft

Piston for the 2.25L 4-cylinder petrol engine, forming the reciprocating member within the cylinder bore that transmits combustion pressure through...

Flywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...

Driveshaft Oilpump

Front outer wing RH SIII plastic

Piston Ring Set for one piston in the engine's piston and cylinder assembly. The rings seat in the piston ring grooves, sealing combustion pressure...

Quarterback chassis for Serie 2/3 88" military, including Lightweight. The rear spring leaf supports are included, as well as the support of the fi...

Diesel Stop Control Cable operates the engine stop on the diesel injection pump. Pulling the dashboard control draws the cable to move the fuel sh...

Drive Belt in the accessory belt drive of the Rover V8 engine. It transmits power from the crankshaft pulley to the air conditioning compressor.

Valve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...

Nut FQA

Crankshaft Front Key locates and locks the timing sprocket or front pulley hub to the crankshaft snout, preventing rotational slip between the cran...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Front Fuel Tank Outrigger is a chassis outrigger welded to the main frame rail, located at the rear of the front fuel tank to support and locate th...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Towing Bracket Assembly Front-mounted detachable towing bracket that bolts to the front chassis to provide a towing and recovery point at the front...

O-Ring for use in two distinct applications on classic Land Rover engines. On the Series IIA 2.6L 6-cylinder engine, this O-ring seals the cylinde...

Valve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...