Land Rover Parts

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Spare Wheel Cover in plain black vinyl, sized to fit a 600 x 16 spare wheel and tyre (roughly a 195/80 R15 metric equivalent). It slips over the m...

Contact Set for the Lucas distributor fitted to Land Rover petrol engines, comprising the breaker point assembly within the conventional ignition s...

Windscreen Clamp - secures the classic fold-flat windscreen frame in its upright position. Mounted at the base of the windscreen frame, the clamp ...

Throttle Lever A lever in the accelerator (throttle) linkage of the carburettor V8. It transmits movement from the accelerator cable to the carbur...

Seat Back - Inner - Standard - Black for the centre position of the three-abreast front bench seat in Land Rover Series vehicles. This vinyl seat ...

Radiator Muff - Black is a fabric cover that fits over the radiator grille to control airflow through the radiator. Restricting cold air across th...

Distance Piece for the LT76 gearbox mainshaft. This spacer maintains the correct axial position of components along the mainshaft within the LT76 ...

Pop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...

Piston for the 2.25L petrol engine, running in the cylinder bore as part of the piston and connecting-rod assembly. Supplied at +0.020" oversize, ...

Rear Halfshaft for the E.N.V. heavy-duty rear axle, left-hand side. The halfshaft transmits drive from the differential through the axle casing to...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Exhaust Tailpipe forming the final section of the exhaust system on the 109" Stage One V8. This pipe routes exhaust gases rearward from the silenc...

Spring for Land Rover body and chassis application.

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Oil Seal Retainer for the front axle. It retains the oil seal at the swivel pin bearing housing, holding the seal that runs against the halfshaft.

Brake & Clutch Reservoir Tank Kit, a replacement for the original single fluid reservoir that fed both the brake and clutch master cylinders. ...

Layshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Size/Diameter: 1 inch

Piston Ring Set for one piston in the engine's piston and cylinder assembly. The rings seat in the piston ring grooves, sealing combustion pressure...

Jubilee Hose Clip for securing rubber hoses at coolant pipe, heater hose, and similar fluid circuit connections. The worm-drive band tightens evenl...

Spring Washer is a split spring lock washer used at the top of the steering column, at the steering box. Fitted under the securing nut, it maintai...

Exhaust Valve for the 2.25L 4-Cylinder Petrol engine, fitted in the cylinder head valvetrain assembly. This valve operates in the cylinder head to...

Inlet Valve for the cylinder head valve train, with a 34.5 mm head diameter. The inlet valve opens on the induction stroke to admit the air/fuel c...

Blanking Plug - Metric - Cylinder Head Rear seals the rear coolant gallery opening in the cylinder head on Land Rover 4-cylinder engines. The rear...

Conrod Bolt for Land Rover petrol and diesel four-cylinder engines. This bolt secures the connecting rod cap to the connecting rod, clamping the b...

Blanking Plug - plastic plug sealing a 1-1/4" (32mm) diameter aperture in the rear cross member. Installs into unused or access holes in the bodys...

Clevis Pin connecting the brake pedal push rod to the master cylinder actuation linkage. This pin forms the pivot joint between the brake pedal ar...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Pan Head Screw - a 2BA x 1/2 inch slotted pan head fastener used across interior trim and body panel fixings. It retains interior trim panels and ...

Push Rod for the 2.6L 6-cylinder petrol engine fitted to Series II, IIA, and III Land Rovers. This push rod operates within the valvetrain of the ...

Nyloc Nut M5 - M5 hex nyloc (nylon insert) locknut. The nylon insert creates friction against the thread to resist loosening under vibration. Stan...

Locating Screw for the engine. A locating screw sets and holds the position of a component against its mounting during assembly. Applies to the 2....

Washer

Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...

Rocker Bracket Locating Dowel for the cylinder head and rocker assembly in the 2.25L and 2.5L petrol and diesel engines. This dowel locates the ro...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Stud for use in Land Rover gearbox assembly.

Distance bush mainshaft

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Screw for use in Land Rover body, chassis, and hardware applications.

Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...

Blanking Plug for the instrument panel, fitted to close an unused aperture in the dashboard where an instrument, switch or gauge is not installed. ...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Differential Crown Wheel Locking Tab is a tab washer used in the axle differential assembly to lock and retain the crown wheel bolts after tighteni...