Land Rover Parts

Main Bearing Set for the 2.25L 4-cylinder petrol and diesel engine, supplied in 0.030" oversize. The main bearings are the replaceable shell beari...

Thrust Washer

Main bearing set for the three-bearing 2.25L four-cylinder engine, forming the crankshaft support in the cylinder block bottom end. The shells loc...

U-Bolt clamping a leaf spring to the axle casing in the leaf spring suspension mounting. The bolt passes over the axle casing and draws the spring...

Pre-shaped rear brake pipe for the rear hydraulic braking circuit, carrying fluid from the axle-mounted T-piece to the rear wheel cylinder. The pi...

Bulkhead Mudshield, left-hand - inner wing to bulkhead splash plate, right-hand drive applications. The mudshield closes the gap between the inner...

Bulkhead Mudshield, right-hand - inner wing to bulkhead splash plate, right-hand drive applications. The mudshield closes the gap between the inne...

Door Seal - Bottom for the left-hand front door, forming part of the door-aperture weather sealing. The seal fits along the lower edge of the door...

Door Seal for the rear end door, fitting along the lower floor edge of the side-hinged tailboard. It forms the sealing interface between the foot o...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...

Thermostat

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Electronic Ignition Kit for the Rover V8 petrol engine with a points-type distributor. The kit replaces the mechanical contact points and condenser...

Viscous Fan Coupling is the temperature-controlled drive unit between the water pump and the engine cooling fan. It mounts on the water pump shaft...

Steering Damper mounts across the steering linkage to absorb shocks and damp oscillation (bump steer and wheel shimmy) fed back through the track r...

Steering Damper mounts across the steering linkage to absorb shocks and damp oscillation (bump steer and wheel shimmy) fed back through the track r...

Brake Pipe Set - a complete set of pre-formed steel brake pipes for a single-line hydraulic braking circuit in left-hand-drive configuration. The p...

Brake Pipe Set - a complete set of pre-formed steel brake pipes for the vehicle's hydraulic braking circuit, matched to the Suffix G production spe...

Seat Box Corner Protector set, supplied as a pair to guard the exposed corners of the seat box against knocks and wear. Each protector is CNC cut ...

Brake Kit - a complete rear drum brake overhaul set for the long-wheelbase rear axle, covering both sides in a single kit. It renews the main fric...

Brake Kit - a complete rear drum brake overhaul set for the short-wheelbase rear axle, covering both sides in a single kit. It renews the main fri...

Brake Kit - a complete front drum brake overhaul set covering both sides of the front axle in a single kit. It renews the main friction and hydrau...

Propshaft UJ Silicone Sleeve fits over the rear propshaft universal joint on 63 mm diameter propshafts. It shields the joint from road dirt, grit a...

B-Post - long-wheelbase Station Wagon with second-row doors. The B-post is the vertical body pillar between the front and second-row door apertures...

8 Driving Lamps In Black

Sliding Window Seal - the replacement rubber sealing strip for the standard rear sliding window kit fitted to hard-top bodies. The seal beds the s...

Swivel Housing Gaiter Kit - Series - Ltwt

Clutch Kit for the 9.5 inch single dry-plate clutch assembly, which sits between the flywheel and the gearbox input shaft and transmits engine driv...

Centre Cubby Box - Techno finish. A console box that mounts on the transmission tunnel between the front seats, providing enclosed central storage ...

High-Top Centre Cubby Box in grey. A Defender-style console box that mounts on the transmission tunnel between the front seats, providing enclosed ...

Lower Door Trim Panel for the left-hand door. This panel covers the lower section of the inner door structure, forming the interior trim surface b...

Lower Door Trim Panel for the right-hand door. This panel covers the lower section of the inner door structure, forming the interior trim surface ...

Wheel Cover 205 x 16

Tailgate Seal Kit for the rear tailboard and tailgate. Reseals the rear tailboard and tailgate opening. The kit contains two tailboard seals, one ...

LED Light Kit upgrades the exterior lighting to a coloured-lens LED set. It comprises two front sidelights, two front and two rear indicators and t...

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

Piston for the 3.5L V8 petrol engine, standard (nominal) bore size. It reciprocates within the cylinder bore, transmitting combustion pressure thr...

Fuel Level Sender for the petrol fuel tank, part of the fuel gauge system. The sender mounts in the top of the rear fuel tank, where a float arm f...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...