Land Rover Parts

Inlet Rocker Bush for the valve gear, forming the bearing surface between the inlet rocker arm and the rocker shaft. The bush locates the inlet ro...

Tailgate Hinge Bolt secures the tailgate hinge to the rear body in the tailgate hinge assembly. Used on High Capacity Pick Up (HCPU) body configur...

Door Check Strap Bracket – Rear – RH mounts the door check strap on the right-hand rear side door. The check strap limits how far the door swings ...

Coolant Temperature Sensor - screws into the thermostat housing as part of the engine cooling system. It senses coolant temperature in the thermos...

Mainshaft Thrust Washer for the Series I and Series II gearbox assembly. This 0.135 in (135 thou) washer controls the axial location of 3rd gear o...

Side Step Tread Rubber

Female Dovetail for the rear end door latch mechanism. Receives the male dovetail to align and secure the rear door as it closes. Sold individually.

Track Rod Retainer for the Series Land Rover steering system. This retainer secures the protective rubber gaiter at the track rod end, holding it ...

Washer for the LT95 four-speed gearbox. It is an internal washer within the gearbox assembly.

Vacuum Advance Hose for the carburettor-fed 2.25L 4-cylinder petrol ignition system. This hose carries ported vacuum from the carburettor to the d...

Spacer

Dashboard Light Switch for Land Rover Series II, IIA, and III. This switch assembly controls the dashboard illumination circuit within the electric...

Floor Mat for the second seat row, a ribbed rubber mat protecting the intermediate floor area. Approximate dimensions 1490 x 460 x 3 mm.

Crown Wheel & Pinion is the final-drive gear set within the differential, transferring drive from the propshaft into the axle and turning it th...

Differential Lock Switch mounted on top of the transfer gearbox. It senses engagement of the differential lock and completes the circuit to the das...

High Range Intermediate Gear for the LT95 four-speed gearbox with integral transfer case, as used behind the V8 engine. The gear is carried on the...

Reinforcement is a structural stiffener for the lower rear body. It fits to the lower section of the rear body structure to add rigidity to the sur...

Blanking Plug for the gearbox top cover. It blanks off an unused threaded aperture in the top cover of the LT76 gearbox.

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Number Plate Lamp Plinth is the mounting base for the rear number plate lamp, fixing the lamp unit to the bodywork above the number plate. It loca...

Front Bumperette - a compact protection unit fitted at the front of the vehicle. It provides localised impact protection to the front end. Manufac...

Accelerator Cable Dutch Lightweight Diesel

Fastener Trim Nail used to secure seat trim panels to the seat frame on Land Rover Defender front and centre seat assemblies. This push-fit trim p...

Thrust Washer - intermediate shaft thrust washer for the LT95 four-speed gearbox. It controls the end-float of the intermediate (lay) shaft, takin...

Extended Bulkhead Upper Repair Panel Set restores the upper section of the bulkhead, the structural firewall panel that separates the engine bay fr...

Front Chassis Leg for the right-hand (offside) front of the chassis. A welded chassis repair section that renews the front chassis leg where the o...

Door Mirror - complete exterior door mirror for rearward vision. It fits to the door-mounted mirror arm and carries a convex polycarbonate lens (2...

Shock Absorber Boots are protective covers that fit over the shock absorber body to shield the shaft and seal from mud, grit and debris. Supplied ...

Support Bracket for the upper rear body section, forming part of the rear body-to-chassis structure. It locates and supports the upper rear body p...

Cylinder Head Shroud - the injector shroud fitted into the cylinder head of the 2.25L diesel engine. It seats in the head around the injector, shi...

Door Bottom for the left-hand side, forming the lower section of the door assembly. This is a repair panel that replaces the lower portion of the ...

Second Gear Assembly for the manual gearbox gear train. The assembly provides the second-gear ratio, meshing within the constant-mesh gear set to ...

Fuel Pipe Olive is a compression ferrule used to seal a rigid fuel pipe union. The olive is compressed onto the pipe by the union nut to form a le...