Land Rover Parts

Front Mudshield - RHD - Left Hand Side for Series II and IIA Land Rovers. This inner panel sits between the front wing and the engine bay on the l...

Plunger for the transfer box selector mechanism. Locates within the transfer selector assembly to provide positive engagement and detenting of tra...

Woodruff Key - Camshaft Chainwheel for the 4-cylinder engine timing assembly. This Woodruff key locates the camshaft chainwheel on the camshaft no...

External Circlip - retaining circlip fitted within the LT67 main gearbox. Seats in a shaft groove to axially locate a gear, bearing or spacer on i...

Piston Ring Set for the 2.25L 4-cylinder petrol engine, ground to +0.040" (1.0mm) oversize for use with rebored cylinder bores. The rings seal the...

Piston for the 2.25L 4-cylinder diesel engine, machined to +0.040" oversize for a rebored cylinder block. The piston transfers combustion pressure...

Cylinder head petrol 2.25 leadfree

Upgrade your vehicle's lighting with these 8-inch black halogen driving lights. High power 100W lamps with universal fitting, plastic stone guards,...

Gearbox Distance Piece

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Crown Wheel Bolt with British Standard Fine (BSF) thread, used to secure the crown wheel to the differential carrier in early Land Rover axles. Tw...

Circlip - Rear Mainshaft Bearing for the Series Land Rover gearbox. This circlip retains the rear mainshaft bearing within the gearbox casing, pre...

Steel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).

Bolt - M6 metric thread, 70 mm long. A threaded fastener for securing components at a bolted joint. Tightened to the torque specified for the asse...

Drive Screw retaining the direction-indicator switch clamp. A hammer-drive screw used to secure the indicator switch clamp, and the indicator cowl...

Air Vent Mechanism - operating mechanism for the dash-mounted fresh-air ventilator. Controls the opening and closing of the bulkhead air vent flap...

Valve Stem Oil Seal fits over the inlet valve stems to limit oil consumption past the valve guides in the cylinder head. It is used on 2.25L petrol...

Water Pump for the engine cooling circuit, belt-driven from the front of the engine. The pump circulates coolant through the cylinder block, heads...

Door pillar bracket for the left-hand side — the lower bracket that secures the foot of the front door pillar (A-post) to the bulkhead outrigger. ...

Roof Access Ladder - a bolt-on ladder for reaching the roof and roof rack, mounted on the left-hand side of the body. It clamps to the rain gutter...

Valve Spring for the cylinder head valvetrain. Fitted over the valve stem, it holds the valve closed against its seat and keeps the follower in con...

Screw for securing the window catch on Series hard top body variants. Used in the hard top glazing and catch assembly to retain the window catch m...

Transfer Box Gear - High is the high range gear wheel in the Land Rover Series transfer box assembly, fitting Series vehicles from 1948 to 1984. T...

Piston ring set 2.25 petrol .020"" (per zuiger)

Main Bearing Set for the 2.25L 4-cylinder petrol and diesel engine, supplied in 0.020" undersize. The main bearings are the replaceable shell bear...

Fuel Tank Outrigger is a lateral chassis support bracket within the main frame structure. Welded to the chassis side rail, it carries the front mo...

Battery Carrier is the mounting tray that holds and locates the battery, supporting it and retaining it against movement and vibration. It forms t...

Rubber isolator clamp used in the bonnet-mounted jack bracket assembly to secure the jack beam or handle against the bonnet mounting brackets. The...

Fitment: 1.8L K Series petrol models to (VIN) YA999999

Waterproofing Kit - V8 seals the ignition system of the V8 petrol engine against water and damp. The kit waterproofs the distributor and ignition ...

Reverse Gear for the main manual gearbox assembly. When reverse is selected, this gear engages the reverse idler to invert the rotation passed fro...

Intermediate Exhaust Pipe - the centre section of the exhaust system, connecting the front down-pipe to the rear silencer. Routes exhaust gas rear...

Piston Ring Set for the 2.25L 4-cylinder petrol engine, in +0.060 in oversize. Piston rings perform three functions at once: they seal the combust...

Reverse Gear Needle Roller Bearing supports the reverse gear within the four-speed gearbox. It locates on the reverse gear shaft and carries the r...

Shackle Shim Ring - 0.003in shim used to set the gap on extended spring shackles. Fitted against spacer tube 504211 to take up clearance on the sh...

Replace or upgrade the front outer wing panel on your Series 2/3 Land Rover with this aluminium panel designed for Right-Hand Side (RHS) and Left-H...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Main Bearing Set +0.030" 2,25

Rear Door Protection Plate mounts on the exterior of the rear door to shield the panel from stone chips, scuffs and impact damage during loading an...

Exhaust Rocker Shaft is the shaft on which the exhaust rocker arms are mounted within the cylinder head valve train of the 2.6L 6-cylinder petrol e...