Land Rover Parts

Gear Lever Bracket - mounting bracket for the gear change lever on the LT76 gearbox. The gear lever pivots in the bracket, locating the lever over...

1st Speed Gear - first-gear wheel for the LT76 four-speed gearbox. It forms part of the gearbox gear train, meshing with the layshaft to provide t...

Thrust Washer for the LT95 four-speed gearbox, 3.75mm thickness. This selective-thickness washer sets the end-float of the intermediate gear.

Kit contains: 2X MRC6982 2X MRC6980 2X MRC6985

Propshaft Universal Joint for V8 driveline applications. The universal joint lets the propeller shaft transmit drive through the changing angle be...

Layshaft is the countershaft of the manual gearbox, carrying the cluster of constant-mesh gears that transmit drive from the input shaft down to th...

Track Rod Tube - 109.5cm - Part-Threaded Ends

Front Rope Retaining Hook - Left Hand Side for the soft-top hood system on Series and Defender Land Rovers. This hook is part of the hoodstick and...

Hook for the soft top retaining rope, part of the hood and hoodstick assembly. Secures the rope that runs along the soft top drain channels.

Mudshield Output Shaft

Piston Ring Set seals the piston within the cylinder bore as part of the engine's piston assembly, providing combustion sealing, oil control and he...

Rear Seat Frame Support Clip - the retaining clip that secures the rear seat frame to its support bracket. Holds the seat frame located on its mou...

Steel Wheel - a 5.5J x 16 pressed-steel rim finished in Limestone gloss. This is a tube-type rim: it is not sealed for tubeless running and must b...

spring road front SWB 9 leaf Passenger Side

Rear Rubber Mat for the rear floor and load area, cut to suit short-wheelbase County-specification vehicles. The moulded rubber mat protects the r...

Water Temperature Gauge - a 12V dashboard instrument indicating engine coolant temperature. Mounted in the instrument panel, it displays coolant t...

Suitable for negative earth series.

Crankshaft - 3-Bearing

Front Exhaust Pipe for petrol applications. This is the front section of the exhaust system, carrying gases from the exhaust manifold rearward to t...

Distance Piece - a machined spacer in the axle and suspension assembly, specified for the 1-Ton Military configuration. It sets the standoff betwe...

Retainer - LH

Leaf Spring Heavy Duty

Layshaft Sleeve - bearing sleeve fitted to the layshaft (countershaft) in the LT67 main gearbox. Provides the running surface for the layshaft clu...

Spring Road Front SWB 9lf DS

Throttle Cable Bracket within the carburettor throttle control. Anchors the outer throttle cable, providing a fixed abutment so the inner cable ca...

Exhaust Valve for the cylinder head valvetrain of the 3.5 V8 petrol engine. The exhaust valve opens to release burnt gases into the exhaust port a...

Inlet Valve for the cylinder head valvetrain of the 3.5 V8 carburettor petrol engine. The inlet valve seals the intake port against combustion pre...

Bearing layshaft LT95 4-speed manual gearbox for Rover 3.5L V8 - S3 109" Stage One V8 - early 110" V8 (Stage Two) - 101" Forward Control - Classic...

Safari Rear Side Door Top Panel (r/H) - Black Vinyl

Oil pump relief valve washer V8

Valve Spring - V8 is a cylinder head valve spring for the Rover 3.5L and 3.9L V8 petrol engine. The valve spring seats between the cylinder head a...

Camshaft Retaining Plate for the four-cylinder engine. Bolted to the front face of the cylinder block behind the camshaft gear, it locates the cams...

Bolt - 1/2" UNF x 5" used as the centre shackle pin bolt in the leaf spring suspension assembly on 109" 1-Ton models. This bolt secures the centre...

Circlip

Bolt Set Screw 7/16UNC x 1.25" 2.25L diesel: startermotor to engine (Imperial, non-metric engines) 2.6L petrol: oil filter housing to adaptor

Washer fits the clutch cross shaft within the clutch release mechanism. It seats on the clutch cross shaft pin, retaining the pin and setting its ...

Gearbox Selector Block - the in/out selector block for 1st and 2nd gear. Part of the gearbox selector mechanism, guiding the selector movement whe...

Differential Shim, 0.040in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Steel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Stekker 7-polig Pvc

Pipe clamp 109" intermediate exhaust pipe centre bracket (For the bottom bracket use 264889.)

Screw - 10 UNF x 3/8 is a fixing in No.10 UNF (Unified National Fine) thread, 3/8 inch in length, used in fascia and dash assembly applications. Fi...

Small End Bush (gudgeon pin bush) for the connecting rod small end on Land Rover diesel engines. The small end bush is a precision bronze bush pre...

Core Plug - 1-3/8 in. diameter, threaded - for the Series engine block. This threaded plug seals a casting aperture in the engine block, retaining...