Land Rover Parts

Bonnet Prop - the prop rod that holds the bonnet open for engine-bay access. One end pivots from a bracket on the body while the free end locates ...

Front Quarter Chassis is a front corner repair section of the main chassis frame. It replaces a damaged or corroded front quarter of the chassis, ...

Front Backing Panel - Right Hand is a front-section body repair panel fitted to the right-hand side of the Land Rover Series body. It is supplied ...

Side Door is the right-hand cab side door for the Land Rover Lightweight (Air-Portable) specification. It is a hinged body closure for the right-h...

Side Door is the left-hand cab side door for the Land Rover Lightweight (Air-Portable) specification. It is a hinged body closure for the left-han...

Rear Wing Corner Protector is a chequer plate panel that fits over the rear wing corner to shield the bodywork from stone chips, scuffing and impac...

Rear Wing Corner Protector is a chequer plate panel that fits over the rear wing corner to shield the bodywork from stone chips, scuffing and impac...

Rear Wing Corner Protector is a chequer plate panel that fits over the rear wing corner to shield the bodywork from stone chips, scuffing and impac...

Wheel Arch Eyebrow Moulding Set is a set of four ABS-plastic wheel-arch eyebrow mouldings (spats), one for each wheel opening. The mouldings fit ar...

Bumper top SIII/90/110

Crossmember Cover - a cover panel for the chassis crossmember, forming part of the chassis and body structure.

Rear Half Chassis - replacement rear section of the ladder-frame chassis, supplied as a pressed and welded assembly in the short-wheelbase length. ...

CD Series Lightweight LHP23

Thrust Washer and Pin for the LT95 four-speed gearbox, 3.79mm thickness. This selective-thickness washer, with its locating pin, sets the end-float...

Intermediate Gear with 45 teeth for the LT95 four-speed gearbox and integral transfer case. The gear runs on the intermediate shaft and forms part...

Thrust Washer locates the reverse idler gear on its shaft within the four-speed gearbox. It fits over the reverse idler shaft and bears against th...

Sliding Block forms part of the first-gear synchroniser assembly within the four-speed LT95 gearbox. It locates in the synchroniser hub and transm...

Front Door Armrest for the right-hand front door, mounting to the door trim. The armrest fixes to the inner door, giving the occupant a padded res...

Door Trim Set - full front door trim panels for the interior door assembly, supplied as a matched pair for the two front doors. Each panel carries...

Front Seat Set - a complete front seating set for the cabin interior, supplied as six pieces and finished in Elephant Hide Grey vinyl. The set pro...

Front Centre Seat with Headrest - a middle front seat that fits between the two outer front seats to provide a third front seating position. Trimm...

Hood Stick Set - the tubular frame that supports the canvas hood (soft top) over the rear load area of a metal-cab vehicle. This is the 3/4-length...

Cubby Box - XS, Vinyl - a storage box that fits in the space between the two front seats, providing an enclosed stowage compartment with a lift-up ...

Hardura Insulation Matting Kit - a front cab matting kit that lines the floor and footwell area, reproducing the original factory cab interior fini...

Cubby Box in the compact XS size, a centre console storage unit that mounts between the front seats. It provides an enclosed storage compartment a...

Static Lap Belt is a fixed-length, non-retracting lap belt for centre and rear load-area seating positions. It restrains the occupant across the l...

Flywheel for the 2.25L four-cylinder petrol engine built on the five-main-bearing crankshaft. It bolts to the rear flange of the crankshaft and for...

Vacuum Pipe carries the vacuum advance signal from the left-hand carburettor to the distributor. It connects the carburettor vacuum take-off to th...